background image

3

 WARNING

Always observe

Protect the product with a wiring circuit breaker (I

n 0.03A and 

25A differential switch, 20A magnetic thermal switch) and ground 

fault circuit interrupter (GFCI).

Install both switches outside of the bathroom.
Attach the tap water supply equipment to the bathtub.
Make sure to connect the ground wire (ground).

Use the specified AC voltage for the voltage.

 

●This may result in damage or failure to the device or a fire.

After completing the installation, make sure to check the 

operation of the wiring circuit breaker and ground fault circuit 

interrupter (GFCI).

 

●If the GFCI is not properly operating, it may result in a fire or electric 

shock.

Make sure to install the bathtub according to the installation 

guide and in a stable location that can withstand its mass.

 

Defective installation can result in an injury caused by the bathtub falling or 

flipping over.

Turn the wiring circuit breaker off during operation.

 

This may cause electric shock.

Ensure that you have an ergonomic working position during 

transport and assembly.

 

Take care at every stage that your move is safe. Ensure that you have 

assistance to avoid risk of accident or injury.

Observe the current local prevention of accidents and building 

regulations as well as sanitary and environmental protection 

rules during installation.

Use a fixed connection to supply power to the bathtub.

Do not extend or relay the power cord, connect it as 1 cord.
When installing the bathtub, do it within the protection area and 

make sure that the person does not touch any electrical devices 

from inside the bathtub.

Install the bathtub over 600 mm away from any electrical 

appliances or power sockets.

Stabilise the bathtub with a fixing plate.

 

The bathtub may shake if it is not properly stabilised.

Secure enough space between the bathtub and tiles, and fill that 

space with silicone that does not contain alcohol.
Check to see that the hole positions are not overlapping with the 

cavity portions of the tile base.

 

If there are cavities, use an adhesive anchor to stabilise.

Summary of Contents for PJYD2200PWEE





















Reviews: