manualshive.com logo in svg

TOTALINE TOTALINE P707, Installation And Operation Instructions Manual

Share
Download
TOTALINE TOTALINE P707 Installation And Operation Instructions Manual Download Page 9

9

Step 8 — Install Accessories —

Install all accesso-

ries. Field-installed accessories include:
• Remote Intellitek control
• Dehumidistat
• Remote override timer

Refer to the accessory installation instructions for more in-

formation. See Fig. 25 for wiring.

Step 9 — Electrical Connection to Furnace
(Air Systems Directly Connected to Fur-
nace) —

When the HRV is directly connected to the

furnace, the furnace may need to be interlocked with the HRV

to provide air circulation for the system. Connect the R and G
terminals on the furnace to the COM and N.O. terminals on the
HRV. See Fig. 26 for a wiring diagram. Never connect a
120-vac circuit to the terminals of the HRV control contacts.
Use only low-voltage furnace blower control contacts.

On some older thermostats, energizing the R and G

terminals at the furnace has the effect of energizing Y at the
thermostat and therefore energizing the cooling system. For
these thermostats, use the alternate control contacts wiring. See
Fig. 27.

Magnehelic

Magnehelic

OUTDOORS

PLACE PITOT TUBE A MINIMUM OF 18" FROM BLOWER OR ELBOWS

NOTE: DUCT CONNECTIONS MAY VARY,

DEPENDING ON MODEL.

MAGNEHELIC

GAGE

PITOT

TUBE

PITOT

TUBE

MAGNEHELIC

GAGE

*Pitot tube should be kept at least 12 in. away from fans elbows and dampers to ensure accurate reading.

Fig. 24 — Pitot Tube Balancing

EDF5 (5MR)

OVERRIDE, STAND-BY, CONTINUOUS,

RECIRCULATION & CYCLE/HOUR

2 WIRES

15-MINUTE TIMER

(UP TO 5 TIMERS) 

2 WIRES

DEHUMIDISTAT

2 WIRES

DIAGNOSTIC

LED

CUSTOM DEFROST

MODE JUMPER

SELECTION

3 POSITION MODE

SELECTION

SWITCH

ACCESSORY CONTROL CONTACT

(OPEN & CLOSES CONTACT

WHEN HRV IS ON/OFF)

DEHUM.

WALL CTRL

TIMER

+        -

OVERRIDE CONTROLS / CONTR LES DE LA DEMANDE

HUMIDITY
HUMIDIT

%

MODE CONTROLS / CONTR LES POUR LES MODES

TIMER / MIN.

FILTER / FILTRE

OVERRIDE
ECHANGE

CYCLE

PER HR/ PAR HRE

MODE SPEED

VITESSE DU MODE

MODES

POWER

totaline

fi

15 min.

NOTE: A WIRING DIAGRAM OF THE COMPLETE UNIT IS INSIDE ACCESS PANEL

Fig. 25 — Electrical Connections

NOTE: A wiring diagram of the complete unit is inside access panel.

Summary of Contents for TOTALINE P707

















Reviews:

No comments

Brands by name

Popular brands

Load more brands