background image

57

Others

56

List of supported signals (RGB signals)

This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.

Resolution

720 x 400
640 x 480

800 x 600

832 x 624

1024 x 768

1152 x 864
1280 x 960

1280 x 1024

1400 x 1050
1600 x 1200

Mode

720x400_85

VGA_60
VGA_72
VGA_75
VGA_85

SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85

MAC16"

XGA_60
XGA_70
XGA_75
XGA_85

MAC19"

SXGA1_75

QuadVGA_60
QuadVGA_85

SXGA3_60
SXGA3_75
SXGA3_85

SXGA+

UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85

Refresh rate

(Hz)

85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
59.978
60.000
65.000
70.000
75.000
85.000

H-frequency

(kHz)

37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
65.317
75.000
81.250
87.500
93.750

106.250

Clock

(MHz)

35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
65.000
75.000
78.750
94.500
79.857

108.000
108.000
148.500
108.000
135.000
157.500
121.750
162.000
175.500
189.000
202.500
229.500

Note

• Signals whose resolution exceeds the native resolution (1024 

×

 768 pixels) will be

compressed. For this reason, some information may be lost, or image quality may be
affected.

Specifications

List of general specifications

Item

Specification

Consumption Power

TLP-X2500: 300 W
TLP-XC2500: 300 W

Weight

TLP-X2500: 2.8 kg
TLP-XC2500: 4.0 kg

External Dimensions

TLP-X2500: 288 

×

 92 

×

 247 mm (W 

×

 H 

×

 D)

(including protruding parts)

TLP-XC2500: 370.5 

×

 92 

×

 249 mm (W 

×

 H 

×

 D)

Cabinet material

PC resin and PC+ABS resin

Conditions for usage environment Temp: 5

°

C to 35

°

C; relative humidity: 30% to 70%

Display method

3-panel transmission

LCD Panel

Panel size

0.63 type

Drive system

TFT active matrix

Picture elements

786,432 pixels (1024H 

×

 768V)

Lens

Zoom lens      F=1.6-1.88   f=18.6-22.3 mm

Lamp

High-pressure mercury lamp (200 W)

Projection screen size

33-300 inches

Projection distance

1.15-8.80 m

Speaker

1W (Mono)

COMPUTER 1

Mini D sub 15 pin  RGB / Y/P

B

/P

R

 (dual use)

IN terminal
COMPUTER 2

Mini D sub 15 pin  RGB / Y/P

B

/P

R

 / MONITOR OUT (dual use)

IN terminal
S-VIDEO terminal

Mini DIN 4 pin

AUDIO (L/R) terminal

RCA Pin Jack 

×

 2

VIDEO terminal

RCA Pin Jack

AUDIO IN terminal

3.5mm dia. stereo mini-jack

AUDIO OUT terminal

3.5mm dia. stereo mini-jack

CONTROL terminal

Mini DIN 8 pin (RS-232C)

Document camera specifications
(Models equipped with document camera)

Item

Specification

Cameral lens

F=3.0, f=9.6 mm

Focus adjustment

Manual

Zoom adjustment

None (Adjust with the distance from the object)

Image Pick-Up Device

3 million pixel 1/2" color CMOS Sensor

Pixels

QXGA (horizontal 2048 

×

 vertical 1536)

Illumination

High brightness LED LED illumination

Notes

• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added

in the future.

Connection ter

minal

Summary of Contents for TLP X2500
































Reviews: