background image

APPENDIX 1  SPECIFICATIONS 

ENGLISH VERSION EO1-33036 

A1.3 Media 

 

EA1- 4 

 

A1.3.2 

Detection Area of the Transmissive Sensor (Cont.) 

<Tag paper with square holes> 

 

 

 

 

 

 

 

 

 

A1.3.3 

Detection Area of the Reflective Sensor 

The Reflective Sensor is movable from the centre to the left edge of media. 
The reflection factor of the Black Mark must be 10% or lower with a waveform length of 950 nm. 
The Reflective Sensor should be aligned with the centre of the Black Mark.   
 
 
 
 
 
 
 
 
 
 
 
 

A1.3.4 

Effective Print Area 

The figure below illustrates the relation between the head effective print width and media width. 
 
 
 
 
 
 
 
 

Sensor should be positioned at 

the centre of the black mark. 

Centre of media 

Min. 12 mm 

Media feed direction 

Min. 2.0 mm 

Sensor is movable 
within this range. 

 

6.0 
mm

 

140 mm (Max. media width) 

128.0 mm

±

0.2  

(Head Effective Print Range) 

Out of print range 

Out of print range 

6.0 
mm

 

Detecting the black 
marks on the back. 

Sensor position 

Centre of media 

Min. 12 mm 

Media feed direction 

Min. 2.0 mm 

Sensor is movable 
within this range. 

Square holes 
(Round holes are not acceptable.) 

Print side 

NOTE: 
Round holes are not acceptable.  

Summary of Contents for TEC B-SX5T Series

























































Reviews: