Toshiba TCB-SC640U-E Owner'S Manual Download

Page: 9 / 67

Central remote controller

Owner’s Manual

-EN

* Please refer to the installation manual for details.

Icon List (Air conditioner)

No.

Icon

Description

An abnormality is occurring. Check with “Check history” (P.62), and contact the dealer from whom
you purchased the product.

A notice code is occurring. Check with “Notice history” (P.62).

Displayed when it is time to clean the filter. (P.48)

Displayed when preparation for heating is in progress.

Displayed when preparation for operation is in progress.

The temperature acquired from the indoor unit is displayed only in the “Control” screen of Unit.

Displayed when Energy saving operation is set. (P.51)

Displayed when this unit is set to Local Control Mode.*

Displayed when the operation of the local remote control connected to each air conditioner is
restricted.
For details, see “Lock the local remote control operation (Key lock)” (P.52).

Displayed when Bypass is set.

Displayed when Automatic is set.

Displayed when Heat exchange is set.

Displayed when a schedule is set.

Displayed when the Emergency system signal (external input) is detected.*

Displayed when the Power peak cut signal (external input) is detected.*

Displayed when the Night operation signal (external input) is detected.*

Displayed when the Lock signal (external input) is detected.*

Displayed during Daylight-saving.

Summary of Contents for TCB-SC640U-E




































































Search results

Summary of Contents for TCB-SC640U-E

Reviews:

Related manuals for TCB-SC640U-E

Brands by name

Popular brands

Toshiba TCB-SC640U-E, Owner'S Manual

Search results

Summary of Contents for TCB-SC640U-E

Reviews:

Related manuals for TCB-SC640U-E

Brands by name

Popular brands