background image

� 5 �

9-EN

10-EN

 WARNING

 • 

When the air conditioner cannot cool or heat a room well,  

    contact the dealer from whom you purchased the air 

    conditioner as refrigerant leakage is considered as the  

   cause.

    In the case of repair that requires refill of refrigerant, ask  

    service personnel about details of the repair.

    The refrigerant used in the air conditioner is harmless.

    Generally, the refrigerant does not leak. However, if the 

    refrigerant leaks in a room and a heater or stove burner in the  

    room catches fire, it may generate toxic gas.

    When you ask service personnel for repairing refrigerant 

    leakage, confirm that the leakage portion has been completely  

   repaired.

 • 

Do not install the air conditioner in a location that may be  

    subjected to a risk of exposure to a combustible gas.

    If a combustible gas leaks and becomes concentrated around  

    the unit, a fire may occur.

 • 

Install the refrigerant pipe securely during the installation  

    work before operating the air conditioner.

    If the compressor is operated with the valve open and without  

    the refrigerant pipe, the compressor sucks air and the 

    refrigeration cycle is over pressurized, which may cause a burst  

    or injury.

 • 

When carrying out the pump-down work, shut down the  

    compressor before disconnecting the refrigerant pipe.

    Disconnecting the refrigerant pipe with the service valve left  

    open and with the compressor still operating will cause air, etc.  

    to be sucked in, raising the pressure inside the refrigeration  

    cycle to an abnormally high level, and possibly resulting in 

    rupturing, injury, etc.

 WARNING

 • 

After installation work, make sure below before operation.

  - Connection pipes are connected properly and no leakage.

  - Packed valves are fully open.

  Running compressor without open packed valves may cause

  abnormal high pressure and parts failure.

  Leakage at connection piping may suck air and make further high   

  pressure cause burst and injure.

 CAUTION

 • 

Do not climb onto or place objects on top of the outdoor unit.

    You may fall or the objects may fall off of the outdoor unit and    

    result in injury.

 • 

Wear heavy gloves during the installation work to avoid 

   injury.

  EQUIPMENT DAMAGE HAZARD

  Failure to follow this caution may result in equipment damage or    

  improper operation.

  Do not bury more than 36 in. (914 mm) of refrigerant pipe in the    

  ground. If any section of pipe is buried, there must be a 6 in. 

  (152 mm) vertical rise to the valve connections on the outdoor units. 

  If more than the recommended length is buried, refrigerant may    

  migrate to the cooler buried section during extended periods of 

  system shutdown. This causes refrigerant slugging and could 

  possibly damage the compressor at start-up.

1131701101-00_S01_297x210_60p_S_p70_220426.indd   5

26/4/2565   11:41:09

Summary of Contents for RAV-SP122AT2P-UL






















Reviews: