background image

– 3 –

Warning indications on the air conditioner unit

n

o

i

t

p

i

r

c

s

e

D

n

o

i

t

a

c

i

d

n

g

n

i

n

r

a

W

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote electric power supplies before servicing.

WARNING

Moving parts. 
Do not operate unit with grille removed. 
Stop the unit before the servicing.

CAUTION

High temperature parts. 
You might get burned when removing this panel.

CAUTION

Do not touch the aluminium fins of the unit. 
Doing so may result in injury.

CAUTION

BURST HAZARD

Open the service valves before the operation, otherwise there might be 

the burst.

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote 
electric power supplies 
before servicing.

WARNING

Moving parts.
Do not operate unit with grille 
removed.
Stop the unit before the servicing.

CAUTION

High temperature parts.
You might get burned 
when removing this panel.

CAUTION

Do not touch the aluminum 
fins of the unit.
Doing so may result in injury.

CAUTION

BURST HAZARD

Open the service valves before 
the operation, otherwise there 
might be the burst.

1

  Precautions for safety

The manufacturer shall not assume any liability for the damage 
caused by not observing the description of this manual.

 WARNING

General

• Before starting to install the air conditioner, read through the 

Installation Manual carefully, and follow its instructions to install 
the air conditioner.

• Only a quali

fi

 ed installer (*1) or quali

fi

 ed service person (*1) is 

allowed to do installation work. Inappropriate installation may 
result in water leakage, electric shock or 

fi

 re.

• Do not use any refrigerant different from the one speci

fi

 ed 

for complement or replacement. Otherwise, abnormally high 
pressure may be generated in the refrigeration cycle, which 
may result in a failure or explosion of the product or an injury to 
your body.

• Before opening the intake grille of the indoor unit or service 

panel of the outdoor unit, set the circuit breaker to the OFF 
position. Failure to set the circuit breaker to the OFF position 
may result in electric shocks through contact with the interior 
parts. Only a quali

fi

 ed installer (*1) or quali

fi

 ed service person 

(*1) is allowed to remove the intake grille of the indoor unit or 
service panel of the outdoor unit and do the work required.

• Before carrying out the installation, maintenance, repair or 

removal work, set the circuit breaker to the OFF position.
Otherwise, electric shocks may result.

• Place a “Work in progress” sign near the circuit breaker while 

the installation, maintenance, repair or removal work is being 
carried out. There is a danger of electric shocks if the circuit 
breaker is set to ON by mistake.

5-EN

6-EN

Summary of Contents for RAV-RM1101CTP-E





























Reviews: