Toshiba RAS-05, RAS-07 Installation Manual Download Page 10 | Manualshive

Page: 10 / 16

Toshiba RAS-05, RAS-07 Installation Manual Download Page 10

8

ELECTRICAL WORKS

ELECTRICAL WORKS

The power supply can be selected to connect to indoor unit or outdoor unit. Choose proper way and connect the power supply and connecting cable by follow
the instruction as following.

Wiring Connection

Indoor unit

Outdoor unit

Valve cover

Terminals block

How to install the air inlet grille on the indoor
unit

• When attaching the air inlet grille, the contrary of the removed operation is

performed.

Wiring of the connecting cable can be carried out without removing the
front panel.

1.  Remove the air inlet grille.
  Open the air inlet grille upward and pull it toward you.
2.  Remove the terminal cover and cord clamp.
3.  Insert the connecting cable (according to the local cords) into the pipe

hole on the wall.

4. Take out the connecting cable through the cable slot on the rear panel so

that it protrudes about 20 cm from the front.

5. Insert the connecting cable fully into the terminal block and secure it

tightly with screws.

6.  Tightening torque : 1.2 N·m (0.12 kgf·m)
7.  Secure the connecting cable with the cord clamp.
8.  Fix the terminal cover and air inlet grille on the indoor unit.

Cord clamp

Terminal cover

Screw

Screws

Air inlet grille

Front panel

1. Remove the valve cover, the electric parts cover and the cord clamp from

the outdoor unit.

2. Connect the connecting cable to the terminal as identi

fi

ed by the

matching numbers on the terminal block of indoor and outdoor unit.

3. Insert the power cord and the connecting cable carefully into the terminal

block and secure it tightly with screws.

4. Use vinyl tape, etc. to insulate the cords which are not going to be used.

Locate them so that they do not touch any electrical or metal parts.

5. Secure the power cord and the connecting cable with the cord clamp.
6. Attach the electric parts cover and the valve cover on the outdoor unit.

Model

RAS-05, 07BKV-E

RAS-10BKV-E

RAS-13BKV-E

RAS-16BKV-E

Power source

50Hz, 220 – 240 V Single phase

Maximum running current

5.0A

6.7A

7.1A

8.0A

Circuit breaker rating

6.5A

8.5A

9.0A

10.0A

Power supply cable

H07RN-F or 60245 IEC66 (1.5 mm

2

or more)

Connecting cable

«
...
8
9
10
11
12
...
»

Summary of Contents for RAS-05, RAS-07

















Reviews:

No comments