manualshive.com logo in svg

Toshiba P000233790, Owner'S Manual

Share
Download
Toshiba P000233790 Owner'S Manual Download Page 48

 

 

8 

Specifications 

Model Name  

PCX5000 

Model Number 

DAZ8850F 

Compliant Standard 

DOCSIS

 

1.0 (1.1Based) 

Computer Interface 

10/100Base-T (10/100Mbps, full/hal f-duplex, auto-sensing)   
4 port;  USB Device (12Mbps, full speed mode) 1 port 

Wireless Interface 

IEEE 802.11b 

Interface 

Cable Interface 

F type female 75ohm 

Demodulation 

64/256QAM 

Physical Speed 

30Mbps (64QAM) /43Mbps (256QAM) 

Frequency Range 

88MHz to 860MHz (edge to edge) 

Bandwidth 

6MHz

 

Receiver  

Input Signal Level 

-15dBmV to +15dBmV  
(Automatically Gain Controlled by CM) 

Modulation 

QPSK / 16QAM 

Physical Speed 

320, 640, 1280, 2560, 5120kpbs (QPSK) 
640, 1280, 2560, 5120, 10240kps (16QAM) 

Frequency Range 

5 to 42MHz (edge to edge) 

Bandwidth 

0.2, 0.4, 0.8, 1.6, 3.2MHz 

Transmitter 

Output Signal Level 

+8dBmV to +58dBmV (QPSK) 
+8dBmV to +55dBmV (16QAM) 
(Output signal level of CM is automatically controlled by CMTS 
through power ranging function) 
Step: 1dB 

Max. Number of CPEs 

NAT-ON: 252 
NAT-OFF: 31 (31 MAC address) 

MAC Address 

1 to 31 (set by MIB) 

LLC 

16 

Filtering 

IP 

32 

Subnet / Mask 

192.168.100.xx  / 255.255.255.0 (factory default) 

Lease Address Range 

192.168.100.2  to 192.168.100.127  (factory default) 

DHCP 
Server 

Reserved Addresses 

192.168.100.128  to 192.168.100.253  (factory default) 

Gateway Address 

192.168.100.254 (factory default) 

HTTP Web 
Server 

LAN-Side Address 

192.168.100.1 
 

Frequency Cache 

4 entries 

Frequency 
Search 

Channel Plan 

Supports 3 North American Channel Plan (STD, IRC, HRC) 

Safety 

UL1950, UL1310 (AC-DC adapter) 

EMC 

FCC Part 15 class B 

AC-DC Adapter 

100-120V

±

10

%

, 50/60Hz  

(Note: AC Adapter itself is 100-240V, but AC cord is 120V) 

Internal Power Supply 

DC 5V 2.4A (change connector) 

Power 
Supply  

Consumption 

10 Watts (approximately)  

Protocol 

SNMP/ICMP 

OSS 

MIB 

MIB II / MCNS MIB / Toshiba MIB 

Operating temperature 

32°F (0°C) to 104°F (40°C) 

Operating humidity 

10% to 90%(Non condensing) 

Environment 

Storage temperature 

-4°F (-20°C) to 140°F (60°C) 

Orientation 

Horizontal and wall mounting 

Reset switch 

Reset to factory default 

LED 

POWER, CABLE, TEST, USB, WLAN, 10/100Mbps[1-4], 
LINK/ACT[1-4]

 

Dimensions (without A C-DC Adapter) 

8.5” x 8”.8 x 1.7” (WxDxH) unit: inch 

Weight 

2.1lbs. (approximately) 

Summary of Contents for P000233790






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands