EN
– 10 –
8
Louver direction
NOTE
• To improve the cooling / heating performance, change
the louver angle for each operation.
• This function is not available for duct type units.
The characteristics of air: Cool air falls, and warm
air rises.
CAUTION
Point the louver horizontally during cooling
If pointing downward for cooling, dew may form on the
surface of the air discharge or louver and may drop
down.
NOTE
• If pointing horizontally for cooling, dew may form on
the surface of the cabinet or louver and may drop
down.
• If pointing horizontally for heating, the room
temperature may be uneven.
• Do not handle the louver manually.
Doing so may cause a failure.
Use the SWING/FIX button on the remote control to
adjust the angle.
4-way cassette type, Compact
4-way cassette type, Ceiling
type
◆
To set the louver direction
1
Push the
button during running.
The louver direction changes with each push of
the button.
◆
To start swinging
1
Push the
button repeatedly to set the
louver direction to the lowest position, then
push
again.
The SWING
indicator is displayed and the
louver begins swinging.
▼
For heating (For heat-pump model only)
Point the louver downward.
If not pointing downward, hot
air may not reach the floor.
▼
For cooling
Point the louver horizontally.
If pointing downward, dew
may form on the surface of
the air discharge port and
may drop down.
▼
For fan
Select a wind direction.
▼
In all operations
SWING/FIX
Initial setting
Initial setting
Initial setting
SWING/FIX
SWING/FIX
Repeat
◆
To stop swinging
1
Push the
button at the desired
position while the louver is swinging.
•
Push the
button repeatedly to change
the louver position again.
In this case, push the
button again after 2
seconds.
• In Cool/Dry operation, the louver does not stop
as it directs downward. If stopping the louver as
it directs downward during swing operation, it
stops after moving to the third position from the
highest position.
◆
Unit select
• When two or more indoor units are controlled with
one remote control, the louver direction can be set
for each indoor unit by selecting them individually.
• To set louver direction individually, push the
button (left side of the button) to display an indoor
unit number in the control group. Then set the louver
direction of the displayed indoor unit.
• When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
• Each time the
(left side of the button) is
pushed, the indication changes as follows:
4-way cassette type only
◆
To set the louvers individually
1
Push the
button (left side of the
button) during running to select a unit.
The unit number changes each time the button is
pushed.
• When no unit number is displayed, all units are
selected.
2
Push the
button (right side of the
button) to select a louver.
Each time the button is pushed, the indicator on
the left of the remote control changes as follows:
* When no louver number is displayed, all 4
louvers are selected.
* However, even if the
button is pushed
while the louver is swinging, one of the
indications below may sometimes be displayed
and may not set the louver to the highest
position.
▼
Indications when swinging is stopped
▼
Indications when swinging is stopped
SWING/FIX
SWING/FIX
SWING/FIX
FAN/HEAT
COOL/DRY
SWING/FIX
FAN/HEAT
operation
COOL/DRY
operation
UNIT LOUVER
UNIT LOUVER
Unit No.
1-4
No
display
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
UNIT LOUVER
No
display
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
Unit No.
1-4
UNIT LOUVER
No
display
Louver No.
03
01
02
04
Refrigerant
pipe
Drain pipe
Electrical control box
19-EN
20-EN
+00EH99943901_00Ta.book Page 10 Thursday, May 23, 2013 7:17 PM
