Owner’s Manual
– 10 –
EN
8
Louver Direction
NOTE
To improve the cooling / heating performance, change
the louver angle for each operation.
The characteristics of air: Cool air falls, and warm air
rises.
CAUTION
Point the louver horizontally during cooling
If pointing downward for cooling, dew may form on the
surface of the air discharge or louver and may drop
down.
NOTE
• If pointing horizontally for cooling, dew may form on
the surface of the cabinet or louver and may drop
down.
• If pointing horizontally for heating, the room
temperature may be uneven.
• Do not handle the louver manually.
Doing so may cause a failure.
Use the SWING/FIX button on the remote controller to
adjust the angle.
4-way cassette type, 2-way
cassette type, 1-way cassette
type, ceiling type
To set the louver direction
1
Push the
button during running.
The louver direction changes with each push of the
button.
For heating
Point the louver downward. If
not pointing downward, hot
air may not reach the floor.
For cooling
Point the louver horizontally.
If pointing downward, dew
may form on the surface of
the air discharge port and
may drop down.
For fan
Select a wind direction.
To start swinging
1
Push the
button repeatedly to set the
louver direction to the lowest position, then
push
again.
The SWING
indicator is displayed and the louver
begins swinging.
In all operations
SWING/FIX
Initial setting
Initial setting
Initial setting
SWING/FIX
SWING/FIX
Repeat
To stop swinging
1
Push the
button at the desired position
while the louver is swinging.
• Push the
button repeatedly to change
the louver position again.
* However, even if the
button is pushed while
the louver is swinging, one of the indications
below may sometimes be displayed and may not
set the louver to the highest position.
Indications when swinging is stopped
In this case, push the
button again after 2
seconds.
• In COOL/DRY operation, the louver does not stop
as it directs downward. If stopping the louver as it
directs downward during swing operation, it stops
after moving to the third position from the highest
position.
Indications when swinging is stopped
Unit select
• When two or more indoor units are controlled with one
remote controller, the louver direction can be set for
each indoor unit by selecting them individually.
• To set louver direction individually, push the
button (left side of the button) to display an indoor unit
number in the control group. Then set the louver
direction of the displayed indoor unit.
• When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
• Each time you push the
(left side of the button),
the indication changes as follows:
4-way cassette type 2H series
only
To set the louvers individually
1
Push the
button (left side of the button)
during running to select a unit.
The unit number changes each time you push the
button.
• When no unit number is displayed, all units are
selected.
2
Push the
button (right side of the button)
to select a louver.
Each time you push the button, the indicator on the
left of the remote controller changes as follows:
* When no louver number is displayed, all 4 louvers
are selected.
SWING/FIX
SWING/FIX
SWING/FIX
FAN/HEAT
COOL/DRY
SWING/FIX
FAN/HEAT
operation
COOL/DRY
operation
UNIT LOUVER
UNIT LOUVER
No
display
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
Unit No.
1-4
UNIT LOUVER
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
Unit No.
1-4
No
display
UNIT LOUVER
No
display
Louver No.
Electrical control box
Refrigerant
pipe
Drain pipe
EN-19
EN-20
1FAN_OM_EHV0000101-01.book Page 10 Thursday, September 13, 2018 5:10 PM