Toshiba LONWORKS option unit Communication Function Manual Download Page 25

Page: 25 / 25

E6581467

6. Specifications

Item Specification

Description

Number of domains

Number of address
entries

Number of alias tables

Communication
transceiver

Free topology transceiver
TP/FT-10 channel type

ANSI/EIA/CEA 709.3

Baudrate 78kbps

Protocol LonTalk

ANSI/EIA

709.1

Communication signal

2 wires and shield

NETA, Shield, NETB

Transmission distance

Free topology:

Between devices: 400m or less
Total cable length: 500m or less

Bus topology (both terminated):

Total cable length: 1400m or less
Stub length: 3m or less

When recommended cable is used:
Level 4/22AWG

Number of
Network variables

Input network variables: 7
Output network variables: 12
Configuration properties: 12

Number of connected
nodes

64 nodes at maximum / segment

However, a host and a router are
counted as one node.

Service pin function

Mechanical switch (SW2)

Used for notification of Neuron ID to
the host.

Terminal block

Detachable terminal block 3-pole

Applicable terminal block
Manufacturer: PHOENIX CONTACT
Type-Form : MSTB 2,5/3-ST-5,08

- 24E -

Summary of Contents for LONWORKS option unit


























Search results

Summary of Contents for LONWORKS option unit

Reviews:

Related manuals for LONWORKS option unit

Brands by name

Popular brands

Toshiba LONWORKS option unit, Communication Function Manual

Search results

Summary of Contents for LONWORKS option unit

Reviews:

Related manuals for LONWORKS option unit

Brands by name

Popular brands