background image

 

 

E6581371

c

 

„

 

Wiring

   

 

Warning

 

 

Electrical construction work must be done by a qualified expert. 
Connection of input power by someone who does not have expert knowledge may 
result in electric shocks or fire. 

 Turn off input power before wiring. 

 

Wait at least 10 minutes and make sure that the charge lamp (on the inverter unit) is no 
longer lit. Otherwise, it may lead to electric shocks. 

Mandatory 

 

Tighten the screws on the terminal blocks to the specified torque when connecting 
cables to terminal blocks. 
Otherwise, it may lead to fire.

   

„

 

Operations

 

 

Danger

 

 

 

Do not pull on the cable and connector. 
It may cause damage or malfunctions. 

Prohibited 

 

Use this option under the environment specified in the instruction manual. 
Usage under the environment other than them may cause damages or malfunctions or 
an accident. 

 

 

Use an additional safety device with your inverter or system to prevent a serious 
accident due to the unit malfunctions.   
Usage without an additional safety device may cause an accident. 

Mandatory 

 

Warning

 

 

Set up “Communication error trip function (see below)” to stop the inverter when the 
option unit is deactivated by an unusual event such as an operating error, power 
outage, failure, etc. 

- Communication error trip time 

(

f803

, see the inverter instruction manual for details) 

- Receive heart beat timer 

(See the VF-FS1

 L

ON

W

ORKS

 Communication Function Manual for details) 

Deactivated option unit may cause an accident, if the “Communication error trip 
function” is not properly set up. 

 

Make sure that the operation signals are STOP before clearing the inverter’s fault. The 
motor may suddenly start and that may result in injuries.

 

 

Mandatory 

„

 

Disposal

   

 

Warning

 

 If you dispose off this unit, have it done by a specialist in industrial waste disposal*. 

Improper disposal may result in explosion of capacitors or produce noxious gases, 
resulting in injuries. 
(*) Persons who specialize in the processing of waste and known as “Industrial Waste 
Product Collectors and Transporters” or “Industrial Waste Disposal Persons.” If the 
collection, transport and disposal of industrial waste is done by someone who is not 
licensed for that job, it is a punishable violation of the law (Laws in regard to cleaning 
and processing of waste materials).

 

 

Mandatory 

„

 

Notes on operation

   

Notes

 

 

Avoid

 

installing in a place where ambient temperature or/and humidity change sharply. 

 

 

Keep the transmission cable separate from the power cable of the inverter to prevent the 
inverter from malfunctioning due to electromagnetic noise.   

 

Ground of SHLD terminal on this option at the grounding terminal separated from those 
of inverters and motors. It may cause malfunction due to noise.

 

 

- 3 - 

Summary of Contents for LONWORKS LIU007Z
















Reviews: