Toshiba HCV-6KALU Instruction Manual Download Page 22

Page: 22 / 30

Page 18

MAINTENANCE

Table 2 - Check Points for Periodic Inspection

Check

Point

Check Item

Check Method

Criteria

Disposition

Operating

Mechanism

Loose bolts,

nuts or

screws

Tighten using

screwdriver or

wrench.

Make sure all bolts,

nuts and screws are

tight.

Tighten if loose.

See Table 1 for

tightening torque

specifications.

Dust or

foreign

matter inside

Visual inspection.

The contactor should be

clean and contain no

foreign matter.

Wipe with a clean

dry cloth.

Electro-

magnets

Visual inspection.

Check for rust,

discoloration, wear, or

loose mountings.

Wipe with a clean

dry cloth.

Closing coil

Visual inspection.

Check for discoloration,

and burned parts.

Wipe with a clean

dry cloth.

Spring

Visual inspection.

Check for rust,

deformation,

discoloration, or

damage.

Wipe with clean dry

cloth. Lubricate if

necessary.

Smooth

operation

Visual inspection or

touch. Check

lubrication.

Make sure moving parts

operate smoothly.

Apply a small

amount of

lubrication.

Main Circuit Terminals

and movable

conductors.

Visual inspection.

Tighten using

screwdriver or

wrench.

Make sure there is no

discoloration or loose

fasteners.

Check the cause

and repair. Tighten

connections to the

contactor. See

Table 1 for

tightening torque

specifications.

Loose bolts,

nuts or

screws

Tighten using a

wrench.

Make sure all bolts,

nuts and screws are

tight.

See Table 1 for

tightening torque

specifications.

Vacuum

contact wear.

See Electrical

Service Life (Page

23).

Check contact wear and

wipe.

Replace vacuum

interrupter.

Vacuum

level.

Apply 10kV AC for 1

minute.

Check vacuum level by

withstand voltage test.

If breakdown occurs,

contact Toshiba.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for HCV-6KALU































Search results

Summary of Contents for HCV-6KALU

Reviews:

Related manuals for HCV-6KALU

Brands by name

Popular brands

Toshiba HCV-6KALU, Instruction Manual

Search results

Summary of Contents for HCV-6KALU

Reviews:

Related manuals for HCV-6KALU

Brands by name

Popular brands