background image

   

    D4222901B 

Copyright © 2013 TOSHIBA TELI CORPORATION, All rights reserved.

 

 

 

 

 

 

 

 

www.toshiba-teli.co.jp

 

 

USAGE PRECAUTIONS 

 Handle carefully 

Do not drop the equipment or allow it to be subject to strong impact or vibration, as such action may 

cause  malfunctions.  Further,  do  not  damage  the  connection  cable,  since  this  may  cause  wire 

breakage. 

 Environmental operating conditions 

Do  not  use  the  product  in  locations  where  the  ambient  temperature  or  humidity  exceeds  the 

specifications.   

Otherwise,  image  quality  may  be  degraded  or  internal  components  may  be  adversely  affected.  In 

particular, do not use the product in areas exposed to direct sunlight. 

 Combination of C-mount lens 

Depending on the lens you use, the performance of the camera may not be brought out fully due to 

the  deterioration  in  resolution  and  brightness  in  the  peripheral  area,  occurrence  of  a  ghost, 

aberration and others. When you check the combination between the lens and camera, be sure to 

use the lens you actually use. 

When installing a lens in the camera, make sure carefully that it is not tilted. 

In addition, use a mounting screw free from defects and dirt. Otherwise, the camera may be unable 

to be removed. 

As  for  the  C-mount  lens  used  combining  this  product,  the  projection  distance  from  bottom  of  the 

screw should use 10mm or less. 

10mm or less

C-mount lens

Bottom of
the screw

 

 Mounting to a pedestal 

When mounting this product to a pedestal, make sure carefully that the lens doesn't touch with the 

pedestal. 

 Do not expose the camera’s image-pickup-plane to sunlight or other intense light directly. 

Its inner CMOS sensor might be damaged. 

 Occurrence of moiré 

If  you  shoot  thin  stripe  patterns,  moiré  patterns  (interference  fringes)  may  appear.  This  is  not  a 

malfunction. 

 Occurrence of noise on the screen 

If an intense magnetic or electromagnetic field is generated near the camera or connection cable, 

noise may be generated on the screen. If this occurs, move the camera or the cable. 

Summary of Contents for BU406M




























Reviews: