manualshive.com logo in svg

Toshiba B-FP3D SERIES, Maintenance Manual

Share
Download
Toshiba B-FP3D SERIES Maintenance Manual Download Page 45

© 2016-2019 Toshibatec Corporation All right reserved 

 

B-FP3D Series Maintenance Manual 

 

Revision Record 

Version: 0002 

Page 

Contents 

2-2 

Step 6)  Cover open button 

 Open button 

2-4 

Step 11) For the GH model, procedure for removing the adhesive tape from the 

thermal head assembly has been added.  

2-5 to 2-8 

Step numbers have been corrected. 

2-6 

Step 15) For the GH model, procedure for removing the IP54 sheet from the Battery 

frame has been added.  

2-7 

Step 16) For the GH model, procedure for attaching the sheet to the battery frame 

with after replacing the CPU PC board has been added. 

For the GH model, procedure for attaching new adhesive tape to the thermal head 

assembly has been added.  

2-10 

Step 1) For the GH model, procedure for removing the Thermal head for has been 

added.  

Step 2) For the GH model, procedure for removing the IP54 water resisting 

materials has been added.  

Step 3) For the GH model, procedure for attaching the IP54 water resisting 

materials to the new LCD unit has been added.  

2-12 

Step 2) For the GH model, procedure for replacing the exclusive battery unit and 

attaching new tape to the thermal head assembly has been added.  

2-13 

Step 4) For the GH model, procedure for attaching new adhesive tape to the 

thermal head assembly has been added.  

Step number 4) was missing 

2-16 

Step 5) For the GH model, procedure for removing the adhesive tape from the 

thermal head assembly has been added. 

Step 6) For the GH model, procedure for attaching new adhesive tape to the 

thermal head assembly has been added. 

2-18 

Step 3) Remove the Upper sensor on from the Print Head cover.  

2-19 

Step 5) Explanation of how to remove the black cover has been partly changed. 

Step 6) NOTE: picture below 

 picture above 

Step 7) For the GH model, procedure for attaching new adhesive tape to the 

thermal head assembly has been added. 

2-21 

Step 3) Paper Guide Outlet 

 Paper Guide Assembly 

2-22 

Step 4) Explanation on how to remove the platen roller has been changed. 

2-23 

Step 3) Explanation on how to remove the peel-off unit has been changed. 

2-24 

Step 4) Push 

 Pull 

2-25 

Step 7) For the GH model, procedure for attaching new adhesive tape to the 

thermal head assembly has been added. 

2-26 

Step 3) Explanation on how to remove the peel-off PCB has been changed. 

Step 4) Step number has been corrected.  

For the GH model, procedure for attaching new adhesive tape to the thermal head 

assembly has been added. 

2-27 

Step 2) Add of 2 screws 

Step 3) Roller Clip 

 Roller Clips 

Summary of Contents for B-FP3D SERIES















































Reviews:

No comments

Brands by name

Popular brands

Load more brands