manualshive.com logo in svg

Toshiba B-FP3D SERIES, Maintenance Manual

Share
Download
Toshiba B-FP3D SERIES Maintenance Manual Download Page 43

3. TROUBLESHOOTING

 

EO18-33032 

 

3. TROUBLESHOOTING 

3- 1 

3. TROUBLESHOOTING 

Problems Cause 

Solution 

The printer is not turned 
on. 
 

1. The battery is not loaded correctly.
2. The battery terminal is 

disconnected from the soldering 
part. 

3. CPU PC board ass'y failure or 

Drive PC board ass'y failure 

 

1. Re-load the battery correctly.
2. Replace the battery terminal. 
 
 
3. Replace the CPU PC board ass'y or 

the Drive PC board ass'y. 

 

The printer does not print 
media. 
(The status indicator 
blinks in red.) 
 

1. The media roll is not loaded 

correctly. 

2. The media cover is not closed 

completely. 

3. The media is jammed in the 

printer. 

4. The print head FPC harness or the 

print head element is broken. 

 
5. The print head temperature 

reached the upper limit of the 
operating temperature. 

6. Flash ROM write error or erase 

error occurred. 

7. There is insufficient area in the 

flash ROM. 

8. The print mode is not selected 

correctly. 

1. Re-load the media roll correctly.
 
2. Close the media cover completely. 
 
3. Remove the jammed media and re-

load the media roll correctly. 

4. Replace the print head FPC harness 

or the print head ass'y. 

 
5. Open the media cover and allow the 

print head to cool. 

 
6. Replace the CPU PC board ass'y. 
 
7. Erase the data. 
 
8. Send the correct print mode from the 

PC or handy terminal. 

The printer does not print 
media. 
(The status indicator 
blinks in green or orange.) 
 

1. A communication error occurred.
 

1. Check that the interface cable is 

connected firmly. 
Check the communication parameters.

The printer does not print 
media. 
(The status indicator lights 
in red.) 
 

1. The battery voltage is low.
 

1. Turn off the printer and replace the 

battery with a fully charged one. 

 

The printer does not print 
media. 
(The status indicator lights 
in orange.) 
 

1. The battery is nearly end.
 

1. Turn off the printer and replace the 

battery with a fully charged one. 

 

The 

[FEED] 

button does 

not function. 
 

1. The 

[FEED] 

button is depressed

incompletely. 

 

1. Press the 

[FEED] 

button more 

strongly. 
Replace the CPU PC board ass'y or 
Drive PC Board. 

 

Summary of Contents for B-FP3D SERIES















































Reviews:

No comments

Brands by name

Popular brands

Load more brands