TORREY PINES SCIENTIFIC EchoTherm IN35-12VDC Operating Manual Download Page 4

ENVIRONMENTAL OPERATING CONDITIONS 
 
The IN35 and IN45 are intended for indoor use.  Ambient temperatures for the lab 
should not exceed the range of 15ºC to 22ºC for proper performance of the instrument.  
Temperatures from 5ºC to 40ºC will not affect the structure of the unit.  Maximum 
relative humidity of 80% for temperatures up to 31ºC decreasing to 50% for relative 
humidity at 40ºC should not be exceeded. 
 
This product is suitable for installation category II, pollution degree II. 
 
CONDENSATION 
 
Condensation can occur in the sample chamber when working at very low temperatures 
for long periods in a humid environment.  Precautions should be taken to assure that 
your samples are not affected.  Something as simple as placing a paper towel on the 
bottom of the chamber can help.  If condensation needs to be completely eliminated, a 
good amount of desiccant may be needed.  If condensation occurs, it will run toward the 
front of the chamber where it can easily be cleared.           
 
GENERAL 
 
The IN35 and IN45 are designed for laboratory use and for use only as instructed in this 
manual.  If the instrument is used in a manner not specified by the manufacturer, the 
protection provided in the design of the equipment may be impaired.  
 

V.  SET UP INSTRUCTIONS 

 

The IN35 and IN45 Programmable Digital Chilling Incubators are extremely simple to 
use, set and forget units.  The digital, microprocessor design and PID temperature 
control will assure that the correct temperature as set is attained and held. 
 
SET UP 
 
1.  

Unpack the unit carefully.  Be sure to save the packing material in case the unit 

 

needs to be returned to the factory for service.  

 
2. 

The IN35 weighs 45 pounds (20.4 kg), and the IN45 is 56 pounds (25.2 kg).  
Both are bulky, and have no handles.  It is best to have two people remove the 
unit from its box and place it on the lab bench.  Always cradle the unit from the 
underside.   

 
3.   

Plug the power supply cable into the jack on the rear of the unit.  Plug line cord 
into a properly grounded three-wire outlet of proper voltage. 

 
 

 

 

 

 

 

 

Summary of Contents for EchoTherm IN35-12VDC















Reviews: