Toro Z595-D Z Master Operator'S Manual Download

Page: 3 / 64

(ROPS) .......................................................... 16

Maintenance............................................................... 29

Recommended Maintenance Schedule(s) ................ 29
Lubrication............................................................. 30

Greasing and Lubrication ................................... 30
Greasing the Mower Deck and Belt

Idlers.............................................................. 30

Engine Maintenance............................................... 31

Servicing the Air Cleaner .................................... 31
Servicing the Engine Oil ..................................... 32

Fuel System Maintenance ....................................... 36

Servicing the Fuel Filters .................................... 36
Servicing the Fuel Tank ...................................... 36

Electrical System Maintenance................................ 36

Servicing the Battery........................................... 36
Servicing the Fuses ............................................. 38

Drive System Maintenance ..................................... 39

Adjusting the Tracking........................................ 39
Checking the Tire Pressure ................................. 39
Checking the Wheel Hub Slotted Nut.................. 40
Adjusting the Caster Pivot Bearing ...................... 40
Servicing the Gear Box ....................................... 40

Cooling System Maintenance .................................. 41

Servicing the Cooling System.............................. 41

Brake Maintenance ................................................. 43

Adjusting the Parking Brake................................ 43

Belt Maintenance.................................................... 43

Inspecting the Belts ............................................ 43
Replacing the Mower Belt ................................... 43
Adjusting the Mower Belt Tension ...................... 44
Replacing the PTO Drive Belt............................. 45
Replacing the Pump Drive Belt ........................... 45
Replacing and Tensioning the Alternator

Belt ................................................................ 46

Controls System Maintenance................................. 47

Adjusting the Control Handle Neutral

Position.......................................................... 47

Hydraulic System Maintenance ............................... 48

Servicing the Hydraulic System ........................... 48
Setting the Hydraulic Pump Neutral

Position.......................................................... 50

Mower Deck Maintenance ...................................... 52

Leveling the Mower at Three Positions ................ 52
Servicing the Cutting Blades ............................... 54
Replacing the Grass Deflector............................. 56

Cleaning ................................................................. 57

Cleaning Under the Mower ................................. 57
Waste Disposal ................................................... 57

Storage ....................................................................... 57

Cleaning and Storage .......................................... 57

Troubleshooting......................................................... 59
Schematics ................................................................. 61

Summary of Contents for Z595-D Z Master

































































Search results

Summary of Contents for Z595-D Z Master

Reviews:

Related manuals for Z595-D Z Master

Brands by name

Popular brands

Toro Z595-D Z Master, Operator'S Manual

Search results

Summary of Contents for Z595-D Z Master

Reviews:

Related manuals for Z595-D Z Master

Brands by name

Popular brands