Toro Z595-D Z Master Operator'S Manual Download

Page: 52 / 64

G001066

Figure 71

Double nuts

Locknut

Pump rod

Ball joint

Adjustment bolt

Pumps

Electrical system will not perform proper safety
shut off with jumper wire installed.

•

Remove jumper wire from wire harness
connector and plug connector into seat
switch when adjustment is completed.

•

Never operate this unit with jumper installed
and seat switch bypassed.

7. After both pump neutrals are set, shut off the

machine.

8. Remove the jumper wire from the wire harness

connector and plug the connector into the seat
switch.

9. Install the seat rod and lower the seat into position.

10. Remove the jack stands.

Mower Deck
Maintenance

Leveling the Mower at Three
Positions

Important:

There are only three measuring

positions needed to level the mower.

Setting Up the Machine

1. Position mower on a flat surface.

2. Disengage the PTO, move the motion control levers

to the neutral locked position and set the parking
brake.

3. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

4. Check tire pressure of all four tires. If needed, adjust

to 13 psi (90 kPa)

5. Lower the mower to the 3 inch (76 mm) height-of-cut

position.

6. Inspect the four chains. The chains need to have

tension.

•

If one rear chain is loose, lower (loosen) the front
support arm on the same side. Refer to Adjusting
the Front-to-Rear Mower Pitch.

•

If one front chain is loose, raise (tighten) the front
support arm for that chain. Refer to Adjusting the
Front-to-Rear Mower Pitch.

Leveling the Mower Side-to-Side

1. Position the right blade front-to-rear (Figure 72).

2. Measure the right blade at the

location, from a

level surface to the cutting edge of the blade tip
(Figure 72).

3. Record this measurement. This measurement needs

to be 3-1/8 to 3-1/4 inches.

4. Position the left blade front-to-rear (Figure 72).

5. Measure the left blade at the

location (Figure 72),

from a level surface to the cutting edge of the blade
tip .

6. Record this measurement. This measurement needs

to be 3-1/8 to 3-1/4 inches.

Summary of Contents for Z595-D Z Master

































































Search results

Summary of Contents for Z595-D Z Master

Reviews:

Related manuals for Z595-D Z Master

Brands by name

Popular brands

Toro Z595-D Z Master, Operator'S Manual

Search results

Summary of Contents for Z595-D Z Master

Reviews:

Related manuals for Z595-D Z Master

Brands by name

Popular brands