Toro Workman 07223-90001, Operator'S, Set-Up, And Parts Catalog

Page: 8 / 12

8
5. Secure (92-2667) Attachment Mount Brackets
to (99-0433) Flatbed Assembly using two 1/2”-
16 x 1- 1/2” Lg. Flange Lock Hex. Hd. Cap Screws
and two 1/2” Flange Lock Nuts. Make sure
Attachment Mount Brackets are flush with
Mounting Brackets on Flatbed Assembly. See
FIG. 6. Tighten the six screws and nuts securely,
at this point the Bed should be secure to the
Workman
®
unit.
Base Weight for Bed of Industrial
Workman
®
kit is 350 lb.
Always be sure Lifting device is capable
of lifting bed and any attached
accessory to avoid personal injury or
death.
l
l
l
BED ASSEMBLY 07269:
1. Install four (99-9719) Wear Blocks on the
Flatbed Assembly using eight (two for each
Block) 1/4”-20 x 3/4” Lg. Plain Hd. Screws and
eight 1/4” Flange Lock Nuts. See Illustration on
page 10, (Model No. 07269) Items 2, 3 and 4.
Tighten screws securely. The screw heads
should be recessed into the Wear Blocks’ holes.
2. Attach four (99-0451) Rear Pin Plates on the
(99-0433) Flatbed Assembly using four 1/2”-13 x
4” Lg. Hex. Hd. Cap Screws and four 1/2” Flange
Lock Nuts. The flat part of the plate should be
toward the back of the Flatbed Assembly. See
Illustration on page 10, (Model No. 07269) Item
21. Finger tighten screws and nuts.
3. Remove the four existing (two each side)
1/2”-16 x 1- 1/4” Lg. Flange Lock Hex. Hd. Cap
Screws in the Workman
®
unit. See FIG. 5.
Install two (99-2667) Attachment Mount Brackets
by using the same four 1/2” Flange Lock Hex.
Hd. Cap Screws and 1/2” Flange Lock Nuts that
were removed. Finger tighten screws and nuts.
4. Lower (99-0433) Flatbed Assembly onto the
Workman
®
unit, making sure Rear Pin Plates (99-
0451) clear the channel on the Workman
®
unit.
After positioning bed on unit, slide two (92-1233)
Clevis Pins through the Rear Pin Plates (99-0451)
and through the Workman
®
unit’s Rear Channel
(Rail). Lock (92-1233) Clevis Pins into place by
using four (92-1298) Lynch Pins. Tighten Rear
Pin Plates securely.
SET-UP
WARNING
Lift the cargo bed from four corners
evenly, using Lifing Lugs.
NOTE: Refer to Torque Specifications on page
5 for all Fasteners.
Always remove all cargo (including
welding gas bottles) before lifting bed.
Never lift entire vehicle by the bed
Lifting Lugs.
l
Never pivot bed on Rear Pins. l
Do not exceed capacity. Maximum
capacity, attachments and cargo is 1800
LB (4000 LB. GVW) or 800kg (1800
GVW).
l
Read, understand, and follow Safety
Instructions and Bed Removal
Procedure before servicing vehicle.
FIG. 5
1. Attachment Mount Bracket
2. Existing 1/2” Flange Lock Hex. Hd. Cap Screw
3. Bottle Tray Kit Ass’y (For Reference Only)
3
1645
1
2
FIG. 6
1. Attachment Mount Bracket
2. 1/2” x 1- 1/2” Lg. Flange Lock Hex Hd. Cap Screw
3. Flatbed Mounting Bracket
1646
3
2
1