background image

problems and/or engine damage which may not be
covered under warranty.

Do not use gasoline containing methanol.

Do not store fuel either in the fuel tank or fuel
containers over the winter unless a fuel stabilizer is
used.

Do not add oil to gasoline.

Important:

Do not use fuel additives other than a fuel

stabilizer/conditioner. Do not use fuel stabilizers with an
alcohol base such as ethanol, methanol, or isopropanol.

DANGER

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or explosion
from gasoline can burn you and others and can
damage property.

Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any gasoline
that spills.

Never fill the fuel tank inside an enclosed trailer.

Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 6 to 13
mm (1/4 to 1/2 inch) below the bottom of the
filler neck. This empty space in the tank allows
gasoline to expand.

Never smoke when handling gasoline, and stay
away from an open flame or where gasoline
fumes may be ignited by a spark.

Store gasoline in an approved container and
keep it out of the reach of children. Never buy
more than a 30-day supply of gasoline.

Do not operate without entire exhaust system in
place and in proper working condition.

DANGER

In certain conditions during fueling, static
electricity can be released causing a spark which
can ignite the gasoline vapors. A fire or explosion
from gasoline can burn you and others and can
damage property.

Always place gasoline containers on the ground
away from your vehicle before filling.

Do not fill gasoline containers inside a vehicle or
on a truck or trailer bed because interior carpets
or plastic truck bed liners may insulate the
container and slow the loss of any static charge.

When practical, remove gas-powered equipment
from the truck or trailer and refuel the equipment
with its wheels on the ground.

If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, rather than from a gasoline dispenser
nozzle.

If a gasoline dispenser nozzle must be used,
keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete.

WARNING

Gasoline is harmful or fatal if swallowed. Long-term
exposure to vapors can cause serious injury and
illness.

Avoid prolonged breathing of vapors.

Keep face away from nozzle and gas tank or
conditioner opening.

Keep gas away from eyes and skin.

Using Stabilizer/Conditioner

Use a fuel stabilizer/conditioner in the machine to provide
the following benefits:

Keeps gasoline fresh during storage of 90 days or less.
For longer storage it is recommended that the fuel tank
be drained.

Cleans the engine while it runs

Eliminates gum-like varnish buildup in the fuel system,
which causes hard starting

Important:

Do not use fuel additives containing

methanol or ethanol.

Add the correct amount of gas stabilizer/conditioner to the
gas.

Note:

A fuel stabilizer/conditioner is most effective when

mixed with fresh gasoline. To minimize the chance of varnish
deposits in the fuel system, use fuel stabilizer at all times.

13

Summary of Contents for ProForce 44539

































Reviews: