manualshive.com logo in svg

Toro 68013, Operator'S Manual

Share
Download
Toro 68013 Operator'S Manual Download Page 7

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.

117–2718

125–8175

1.

Read the

Operator’s Manual

for information on greasing

the machine.

125–8216

1.

Read the

Operator’s

Manual

for information on

how to tow the machine.

2.

Warning—limit towing
speed to less than 55 mph
/ 88 km/h.

125–4939

1.

Warning—read the

Operator’s Manual

.

4.

Toxic gas inhalation
hazard—Don’t run the
engine in an enclosed
space.

2.

Hand and arm
entanglement at the
belt drive; crushing hazard
of hand; entanglement
hazard of hand at the
shaft—keep hands away
from moving parts; keep
all guards and shields in
place.

5.

Explosion hazard—stop
the engine and keep
away from flames when
refueling.

3.

Entanglement hazard at
paddles—stop the engine
and wait for all moving
parts to stop before
performing maintenance.

7

Summary of Contents for 68013

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands