manualshive.com logo in svg

Toro 68013, Operator'S Manual

Share
Download
Toro 68013 Operator'S Manual Download Page 12

Engine Controls

1

2

3

4

5

6

7

8

G019744

Figure 15

1.

Recoil-start handle

5.

Fuel cap

2.

Fuel valve

6.

Oil cap/dipstick

3.

Choke lever

7.

Oil-drain plug

4.

Throttle lever

8.

On/Off switch

Fuel Valve

The fuel valve (Figure 16) is located underneath the choke
lever. Move the lever for the fuel valve to the On position
before attempting to start the engine. When you have finished
mixing, stop the engine and move the fuel valve lever to the
Off position.

1

2

3

G018792

Figure 16

1.

Fuel valve

3.

Throttle lever

2.

Choke lever

Choke Lever

Use the choke lever (Figure 16) to start a cold engine. Before
pulling the recoil-start handle, move the choke lever to the
closed position. Once the engine is running, move the choke
lever to the open position. Do not use the choke if the engine
is already warmed up or the air temperature is high.

Throttle Lever

The throttle lever (Figure 16) controls the speed (rpm) of the
engine. It is located next to the choke lever. It sets the engine
speed and therefore can increase and decrease the rotation
speed of the mixing paddles. For best performance, set this
control to the fast position when mixing material.

Engine On/Off Switch

The On/Off switch (Figure 17) allows the operator of the
machine to start and stop the engine. This switch is located
on the front of the engine. Rotate the On/Off switch to the
On position to start and run the engine. Rotate the On/Off
switch to the Off position to stop the engine.

OFF

ON

1

OFF

ON

G021 103

2

Figure 17

1.

Off

position

2.

On

position

Recoil-start Handle

To start the engine, pull the recoil-start handle (Figure 15)
quickly to turn the engine over. The engine controls described
above must all be set correctly for the engine to start.

Oil-level Switch

The oil-level switch is located inside the engine, and it will
not allow the engine to run in the event the oil level is below
the safe operating limit.

12

Summary of Contents for 68013

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands