background image

11

3327-933

Storage

Important: Store the snowthrower in its operating
position and on its wheels. Storing the snowthrower
on its front housing may cause hard starting.

Preparing the Snowthrower
for Storage

Warning

Gasoline fumes are highly flammable, explosive,
and dangerous if inhaled. If you store the product
in an area with an open flame, the gasoline fumes
may ignite and cause an explosion.

Do not store the snowthrower in a house (living
area), basement, or any other area where ignition
sources may be present, such as hot water and
space heaters, clothes dryers, furnaces, and
other like appliances.

Important: Do not use the chute handle to lift the
snowthrower. This can damage the chute handle.

1.

Add a fuel stabilizer/conditioner to the fuel in the

fuel tank as directed.

Note: If you use Toro 50:1 2-Cycle Oil (Fuel
Stabilizer Added)
, you do not need to add a fuel
stabilizer/conditioner.

2.

Run the engine for 5 minutes to distribute the

conditioned fuel through the fuel system.

3.

Stop the engine and allow it to cool.

4.

Use a hand pump to pump the fuel from the fuel

tank into an approved fuel container, or run the
engine until it stops.

5.

Start the engine and run it until it stops.

6.

Choke or prime the engine, start it a third time,

and run the engine until it will not start.

7.

Slowly pull the recoil starter until you feel

resistance due to compression pressure, then stop.

8.

Release the starter tension gradually by allowing

the rope to go back slowly to prevent the engine from
reversing due to compression pressure.

9.

Dispose of unused fuel properly. Recycle it

according to local codes, or use it in your automobile.

Note: Do not store stabilized fuel for more than 90
days.

10. Tighten all loose screws, bolts, and locknuts.
Repair or replace any damaged parts.

11. Clean the snowthrower thoroughly.

12. Cover the snowthrower and store it in a clean, dry
place out of the reach of children. Allow the engine to
cool before storing it in any enclosure.

Folding the Handle

1.

Loosen the knobs and pull out the handle bolts.

2.

Fold the upper handle forward as shown.

m-5537

Summary of Contents for 38536













Reviews: