background image

24

Maintenance

Note: Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule

Maintenance Service

Interval

Maintenance Procedure

Each Use

Engine Oil—check level

Safety System—check

Brake—check

Engine—clean outside

Mower Housing—clean

After first 5 hours

Engine Oil—change

After first 8 Hours

Hydraulic Oil—check

8 Hours

Cutting Blades—check

Mower Housing—clean

Caster Wheels—grease

25 Hours

Foam Air Cleaner—service

1

Paper Air Cleaner—clean

1

40 Hours

PTO Belt Idler Arm—grease

Tires—check pressure

Hydraulic Oil—check

50 Hours

Belts—check for wear/cracks

100 Hours

Engine Oil—change

1

Spark Plug(s)—check

Electric Clutch—adjust

Engine—clean outside

Paper Air Cleaner—replace

1

Hydraulic lines—check

After first 200 Hours

Hydraulic oil filter—change

200 Hours

Oil Filter—change (200 hours or every other oil change)

Fuel Filter—replace

At storage or 400 Hours

Hydraulic oil filter—change

Chipped Surfaces—paint

Perform all maintenance procedures listed above before storage

1

More often in dusty, dirty conditions.

Important

 Refer to your engine operator’s manual for additional maintenance procedures.

Summary of Contents for 30339





















































Reviews: