Toro 30230 Groundsmaster 225 Operator'S Manual Download Page 11

Page: 11 / 32

SET-UP INSTRUCTIONS

WARNING

Connecting cables to the wrong post could

damage the electrical system and result in perĆ

sonal injury.

Note:

Make sure battery cables are routed away from

any sharp edges or moving parts.

Coat the terminal with sealant such as Grafo 112X,

Toro Part No. 505Ć47 and install the rubber boot onto

positive terminal.

CHECK TIRE PRESSURE

The tires are over-inflated for shipping. Therefore,

release some of the air to reduce the pressure. Correct

air pressure in front and rear tires is 20 psi.

INSTALL REAR WEIGHT

Two Wheel Drive Groundsmaster 225 Traction Unit complies with ANSI B71.4-1990 Standard when equipped with

rear weight. 55 lbs. of rear weight is installed, at the factory, on the Groundsmaster 225 Traction Unit. Use chart

below to determine combinations of additional weight requirements. Order parts from your local Authorized Toro

Distributor.

Additional Rear

Weight Required

Left Side Weight

Required

Weight Part

Number

Weight

Description

Qty.

52" Rear

Discharge Deck

(Model 30568)

0 lb.

52" Side

Discharge Deck

(Model 30555)

0 lb.

52" Side

Discharge Deck

with 15 cu. ft.

Hopper

0 lb.

250 lb.

*77-6700

92-9670

24-5780

24-5790

325-14

3253-7

57-4230

3217-9

75 lb. Wheel Weight

Bracket Kit

Rear Weight Kit

Rear Weight-35 lb.

Screw

Lockwasher

Spacer

Nut

62" Side

Discharge Deck

(Model 30564)

70 lb.

0 lb.

24-5780

Rear Weight Kit

62" Side

Discharge Deck

with 9 cu. ft. Hopper

50 lb.

0 lb.

24-5780

Rear Weight Kit

62" Side

Discharge Deck

with 15 cu. ft.

Hopper

0 lb.

180 lb.

*77-6700

92-9670

24-5780

24-5790

325-14

3253-7

57-4230

3217-9

75 lb. Wheel Weight

Bracket Kit

Rear Weight Kit

Rear Weight-35 lb.

Screw

Lockwasher

Spacer

Nut

62" Guardian

Recycler Deck

(Model 30569)

50 lb.

0 lb.

24-5780

Rear Weight Kit

72" Side

Discharge Deck

(Model 30575)

85 lb.

0 lb.

24-5780

24-5790

325-14

3253-7

57-4230

3217-9

Rear Weight Kit

Rear Weight-35 lb.

Screw

Lockwasher

Spacer

Nut

*75 lb. wheel weight (included with a 15 cu. ft. Hopper) required on left wheel

Summary of Contents for 30230 Groundsmaster 225

































Search results

Summary of Contents for 30230 Groundsmaster 225

Reviews:

Related manuals for 30230 Groundsmaster 225

Brands by name

Popular brands

Toro 30230 Groundsmaster 225, Operator'S Manual

Search results

Summary of Contents for 30230 Groundsmaster 225

Reviews:

Related manuals for 30230 Groundsmaster 225

Brands by name

Popular brands