Toro 22291 Operator'S Manual Download Page 11

Operation

Before Operation

Before Operation Safety

General Safety

Become familiar with the safe operation of the
equipment, operator controls, and safety signs.

Check that all guards and safety devices, such as
deflectors and/or grass catcher, are in place and
working properly.

Always inspect the machine to ensure that the
blades, blade bolts, and cutting assembly are not
worn or damaged.

Inspect the area where you will use the machine,
and remove all objects that could interfere with
the operation of the machine or that the machine
could throw.

Adjusting the cutting height may bring you into
contact with the moving blade, causing serious
injury.

– Shut off the engine, remove the ignition key

(electric-start model only), and wait for all
moving parts to stop.

– Do not put your fingers under the housing

when adjusting the cutting height.

Fuel Safety

Fuel is extremely flammable and highly explosive.
A fire or explosion from fuel can burn you and
others and can damage property.

– To prevent a static charge from igniting the fuel,

place the container and/or machine directly on
the ground before filling, not in a vehicle or on
an object.

– Fill the fuel tank outdoors, in an open area,

when the engine is cold. Wipe up any fuel that
spills.

– Do not handle fuel when smoking or around an

open flame or sparks.

– Do not remove the fuel cap or add fuel to the

tank while the engine is running or hot.

– If you spill fuel, do not attempt to start the

engine. Avoid creating a source of ignition until
the fuel vapors have dissipated.

– Store fuel in an approved container and keep

it out of the reach of children.

Fuel is harmful or fatal if swallowed. Long-term
exposure to vapors can cause serious injury and
illness.

– Avoid prolonged breathing of vapors.

– Keep your hands and face away from the

nozzle and the fuel-tank opening.

– Keep fuel away from your eyes and skin.

Filling the Fuel Tank

DANGER

Gasoline is extremely flammable and
explosive. A fire or explosion from gasoline
can burn you and others.

To prevent a static charge from igniting
the gasoline, place the container and/or
machine directly on the ground before
filling, not in a vehicle or on an object.

Fill the tank outdoors when the engine is
cold. Wipe up spills.

Do not handle gasoline when smoking or
around an open flame or sparks.

Store gasoline in an approved fuel
container, out of the reach of children.

For best results, use only clean, fresh (less than
30 days old), unleaded gasoline with an octane
rating of 87 or higher ((R+M)/2 rating method).

Oxygenated fuel with up to 10% ethanol or 15%
MTBE by volume is acceptable.

Ethanol:

Gasoline with up to 10% ethanol

(gasohol) or 15% MTBE (methyl tertiary butyl
ether) by volume is acceptable. Ethanol and
MTBE are not the same. Gasoline with 15%
ethanol (E15) by volume is not approved for use.

Never use gasoline that contains more than
10% ethanol by volume

, such as E15 (contains

15% ethanol), E20 (contains 20% ethanol), or E85
(contains up to 85% ethanol). Using unapproved
gasoline may cause performance problems and/or
engine damage which may not be covered under
warranty.

Do not

use gasoline containing methanol.

Do not

store fuel either in the fuel tank or in fuel

containers over the winter unless you use a fuel
stabilizer.

Do not

add oil to gasoline.

Important:

To reduce starting problems, add

fuel stabilizer to the gasoline all season. Mix the
stabilizer with gasoline less than 30 days old.

Note:

The capacity of the fuel tank is 1.8 L (0.47

US gallon).

11

 

Summary of Contents for 22291





























Reviews: