background image

g283882

Figure 27

1.

Adjuster pin

3.

Groomer drive hex-head

2.

Cotter pin

4.

Reinforcement screw

4.

Restrain the reel for removal; refer to

Restraining

the Reel for Removing Threaded Inserts (page
18)

.

5.

Install the reinforcement screw (Part No.
1-803022—sold separately) to the internal
threads of the groomer drive hex head and
torque to 13.5 N

m (120 in-lbs) as shown in

Figure 27

.

6.

Remove the groomer drive box from the cutting
reel by turning the groomer drive hex-head
(

Figure 27

).

Important:

If the groomer drive box is

installed on the right side of a cutting
unit, turn the groomer drive hex-head
counter-clockwise (right-hand thread) to
remove the drive-box shaft from cutting unit.

Important:

If the groomer drive box is

installed on the left side of a cutting unit,
turn the groomer drive hex-head clockwise
(left-hand thread) to remove drive-box shaft
from cutting unit

Important:

You must use a 6-point socket

with heavy wall.

Cleaning the Grooming
Reel

Service Interval:

After each use

Clean off the grooming reel after using it by spraying
it with water. Do not direct the water stream
directly at the groomer bearing seals. Do not permit
the grooming reel to stand in water so that the
components rust.

Inspecting the Blades

Service Interval:

Before each use or daily

Inspect the grooming-reel blades frequently for
damage and wear. Straighten bent blades with a
pliers and replace worn blades. When inspecting the
blades, check to see that nuts on the right and left
blade-shaft ends are tight.

g010613

Figure 28

1.

Grooming blade

3.

Sharp edges

2.

Dull (rounded) edges

17

 

Summary of Contents for 133-0150





















Reviews: