manualshive.com logo in svg

Toro 07389, Installation Instructions Manual

Share
Download
Toro 07389 Installation Instructions Manual Download Page 13

Declaration of Incorporation

Model No.

Serial No.

Product Description

Invoice Description

General Description

Directive

07389

315000001 and Up

Cab Kit, Workman

MD/MDX/MDX-D Utility

Vehicle

ELECTRIC CARGO BED

LIFT KIT (2014+)

Utility Vehicle

2006/42/EC,

2000/14/EC

Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.

We will undertake to transmit, in response to requests by national authorities, relevant information on this partly
completed machinery. The method of transmission shall be electronic transmittal.

This machinery shall not be put into service until incorporated into approved Toro models as indicated on the
associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in
conformity with all relevant Directives.

Certified:

Authorized Representative:

Marcel Dutrieux
Manager European Product Integrity
Toro Europe NV
Nijverheidsstraat 5
2260 Oevel
Belgium

Tom Langworthy
Engineering Director
8111 Lyndale Ave. South
Bloomington, MN 55420, USA
October 24, 2022

 

Summary of Contents for 07389

















Reviews:

No comments

Brands by name

Popular brands

Load more brands