Toro 04260 Installation Instructions Manual Download Page 1

Form No. 3396-481 Rev B

Counter-Rotating Groomer Drive System

DPA Cutting Units for Greensmaster

®

Flex

1800/2100, eFlex

®

1800/2100, and TriFlex

®

3300/3400 Series Traction Unit

Model No. 04260

Installation Instructions

This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California

to cause cancer, birth defects, or reproductive harm.

Note:

Kit 120–2760 is required when using this kit on

a TriFlex with an electric reel. Contact your Authorized
Toro Distributor for more information.

The following groomer reels are also available for this
product:

18-inch carbide groomer

18-inch spiral brush

18-inch soft grooming brush

18-inch stiff grooming brush

18-inch spring-steel groomer

18-inch thin-spring-steel groomer

21-inch spring steel groomer

21-inch carbide groomer

21-inch spiral brush

21-inch soft grooming brush

21-inch stiff grooming brush

21-inch thin-spring-steel groomer

Contact your authorized Toro distributor for more
information.

© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3396-481* B

 

Summary of Contents for 04260

















Reviews: