Tormach 39045 Installation Manual Download Page 27 | Manualshive

Page: 27 / 32

background image

INSTALLATION

3. Find the threaded hole toward the top center of the left rear panel. Then, loosely install one M5 × 0.8 - 10

screw from the inside of the enclosure.
This screw supports the access panel while you install the remaining fasteners.

Figure 35: Supporting screw inside the left rear panel.

4. Tilt the access panel and put it through the opening on the left rear panel. Then, hang it inside the enclosure

on the installed M5 × 0.8 - 10 screw.

Figure 36: Access panel moving inside the enclosure.

Page 27

©Tormach® 2022
Specifications subject to change without notice.

tormach.com

TD10712: Installation Guide: 770MX Enclosure Kit (0522A)

«
...
25
26
27
28
29
...
»

Summary of Contents for 39045

































Reviews:

No comments

Related manuals for 39045

Brand: Outback Power Systems Pages: 24

Brand: peerless-AV Pages: 22

Brand: VERITAS Pages: 12

Brand: Azio Pages: 7

Brand: AzenX Pages: 9

Brand: MTX Pages: 12

Brand: CHIEF Pages: 8

TouchTunes Fusion DIY

Brand: Octave Pages: 13

Brand: UNICOM Pages: 2

Brand: Bartec Pages: 18

Brand: NetModule Pages: 2

Brand: IBM Pages: 70

Brand: IBM Pages: 104

Brand: IBM Pages: 300

Brand: Lenovo Pages: 154

Brand: Hamlet Pages: 12

Brand: Aerocool Pages: 10

EN-502MT SERIES

Brand: Audio international Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands