Torklift F1008-30 Manual Download Page 3

 

Warnings

 

 

Truck Bed and Camper Protection 

Torklift 

does not

 recommend installing your camper on top of a plastic bed liner 

(or other compressible material such as foam).  These materials can act as a 
spring, causing increased vertical truck camper movement independent of the 
vehicle.  Plastic bed liners can slide on the truck bed surface, and the truck 
camper can slide on top of the bed liner.  Using a plastic bed liner or similar 
compressible material will void your warranty and may additionally cause truck 
bed and/or camper damage.   
 
Minor movement or settling can occur in some incidental harsh driving conditions 
(on or off-road). A rubber bed mat is recommended to protect the truck bed and 
camper, but is not a requirement to maintain the Torklift legendary lifetime 
warranty.  

 

Suspension 

To significantly reduce body roll, sag and sway Torklift strongly recommends the 
StableLoad.  Torklift International StableLoads improve safety, handling, and to 
help level your truck. More information can be found at

 

(

www.Torklift.com/stableload

). 

 
If your truck is additionally equipped with suspension air bags Torklift cautions 
against over pressurization as this may lead to unsafe vehicle handling 
characteristics.  We have found that airbags used in conjunction with StableLoads 
have allowed operators to lower air bag pressure by 50% or more. Only pressurize 
suspension air bags enough to level the truck. 
 

 

Summary of Contents for F1008-30























Reviews: