background image

Warnings 

Truck Bed and Camper Protection 

Torklift 

does not

 recommend installing your camper on top of a plastic bed liner (or other 

compressible material such as foam).  These materials can act as a spring, causing increased 
vertical truck camper movement independent of the vehicle.  Plastic bed liners can slide on the 
truck bed surface, and the truck camper can slide on top of the bed liner.  Using a plastic bed 
liner or similar compressible material will void your warranty and may additionally cause truck 
bed and/or camper damage.   

Minor movement or settling can occur in some incidental harsh driving conditions (on or off-
road). A rubber bed mat is recommended to protect the truck bed and camper, but is not a 
requirement to maintain the Torklift legendary lifetime warranty.  

Suspension 

To significantly reduce body roll, sag and sway Torklift strongly recommends the StableLoad.  
Torklift International StableLoads improve safety, handling, and to help level your truck. 

If your truck is additionally equipped with suspension air bags Torklift cautions against over 
pressurization as this may lead to unsafe vehicle handling characteristics.  We have found that 
airbags used in conjunction with StableLoads have allowed operators to lower air bag pressure 
by 50% or more. Only pressurize suspension air bags enough to level the truck. 

Summary of Contents for C4204
















Reviews: