manualshive.com logo in svg

Torini TC210 CLUBMAXX, Manual

Share
Download
Torini TC210 CLUBMAXX Manual Download Page 14

14

TORINI.COM.AU

WET WEATHER KIT

NOT INCLUDED IN ENGINE KIT - AVAILABLE SEPARATELY

KIT INCLUDES

• WATER REPELLENT FILTER SOCK

• FOAM FILTER ELEMENT

• SNORKEL ASSEMBLY

• MOUNTING BRACKET

• HOSE CLAMP

• TIE STRAPS (2)

CORRECTLY POSITIONED 

1) Loosen the filter Clamp

2) Remove the standard filter assembly

4) Thread tie straps through filter bracket

5) Secure the filter assembly to the bracket using tie straps

3) Fit snorkel adaptor to carburetor

FITMENT GUIDE:

Note: Once mounted, the bracket itself can 

be left on the engine for use at a moment’s 

notice.

Note: Ensure hose clamp is done up

DO NOT USE IN DUSTY CONDITIONS!

WARNING

The Wet Weather Kit minimises water ingestion by the engine, whilst operating in rainy conditions. The rear facing air 

intake, uses the karts forward motion to prevent water droplets directly striking the filter intake area while at the same 

time drawing dry air from one of the most shielded positions available.
• Prevents engine damage due to excessive water ingress into the engine.

• Designed for quick and easy installation or removal under race conditions.

• Maintains near normal engine performance.

Essential to prevent engine damage whilst racing in wet conditions - P/N: TCWWK

Summary of Contents for TC210 CLUBMAXX

















Reviews:

No comments

Brands by name

Popular brands

Load more brands