Torini TC210 CLUBMAXX Manual Download Page 12

Page: 12 / 16

TORINI.COM.AU

TORINI’S RECOMMENDED SETUP:

SETTING 1

• OUTBOARD MOUNT

• RAPID ENGAGEMENT

• RED SPRINGS

Note - Clutch shown as viewed from the open end.

Note - If the kart chatters or shakes,

either try a moderate or slow shoe

setting or white springs.

OUTBOARD MOUNT

RAPID ENGAGEMENT

CLUTCH SETUP

P/N: TC-GEL19219

SHOE SETTINGS:

CLUTCH SETUP:

SETTING 1

SETTING 2

SETTING 3

RAPID ENGAGEMENT

OUTBOARD ROTATION

• SPROCKET ORIENTATION

• SHOE SETTINGS

• SPRING TENSION

MODERATE ENGAGEMENT

SLOW ENGAGEMENT

CLUTCH SPRING: The tension of the clutch spring and clutch shoe setting will determine the clutch engagement

speed and how much clutch slip you will get.

• Engine Idle Speed - 2,000RPM

• Red Spring Engagement Speed - 2,200RPM

• White Spring Engagement Speed - 2,700RPM

SHOE SETTING OPTIONS:

Rapid Setting - Minor Clutch Slip

Moderate Setting - Medium Clutch Slip

Slow Setting - Large Clutch Slip

SPROCKET ORIENTATION: Having the output or drive sprocket mounted outboard is the preferred orientation

for a single engine kart.

FUNCTION: The engine crankshaft is connected to the input of the

clutch via a keyed shaft, while the output sprocket is connected to the

axle by chain. Centrifugal force is used to engage the clutch shoes,

thereby transmitting power from the engine to the drive shaft.

RATIONAL: The clutch design allows for inboard or outboard

mounting of the output sprocket, 3 different shoe engagement

settings, as well as 2 different spring tensions. This allows the clutch

to be “tuned” to suit your karts unique characteristics. With correct

clutch setup and proper gearing, you will feel an even pull coming

out of the corners and constant acceleration on the straights.

Summary of Contents for TC210 CLUBMAXX

















Search results

Summary of Contents for TC210 CLUBMAXX

Reviews:

Brands by name

Popular brands

Torini TC210 CLUBMAXX, Manual

Search results

Summary of Contents for TC210 CLUBMAXX

Reviews:

Brands by name

Popular brands