manualshive.com logo in svg

Torin BIG RED JACKS T30306, Owner'S Manual

Share
Download
Torin BIG RED JACKS T30306 Owner'S Manual Download Page 35

Page 

35

 of 

48

 

 

BEFORE USE 

1. 

Before using this product, read the owner's manual completely and familiarize yourself thoroughly with 
the product and the hazards associated with its improper use. 

2. 

Perform the air purge procedure. (See previous instructions for system purge procedure.) 

3. 

Pour a teaspoon of good quality, air tool lubricant into the air supply inlet of the lift control valve. (See 
illustration) Connect to air supply and operate for 3 seconds to evenly distribute lubricant. 

 

4. 

Check and that the pump operates smoothly before putting into service.   

5. 

This product is fitting use standard 1/4" NPT air fitting. If changing the fitting is required, install a 1/4" 
NPT fitting of your choice, ensure that thread tape or compound is used to seal connection. 

 

6. 

Inspect before each use. Do not use if bent, broken or cracked components are noted. 

 

 

 

AIR/HYDRAULIC CLEVIS BASE LONG RAM JACK 

Summary of Contents for BIG RED JACKS T30306

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands