background image

FRONT PANEL

1- MIC INPUT 
MXi.6FX  is equipped with 2 low-noise microphone preamplifiers with optional 
phantom power, 50 dB of Gain and 115 dB of S/N ratio. You can connect almost 
any type of microphone. Dynamic microphones do not need phantom power. Use 
phantom power only with condenser microphones but make sure that the 
phantom power button is disengaged before connecting the microphone. 
Phantom power will not damage dynamic microphones but it may damage tube or 
ribbon microphones so make sure to read the microphone instructions manual 
before engaging phantom power. Use switch (24) to activate/deactivate phantom 
power. These two channels are also equipped with 1/4" TRS balanced/unbalanced 
LINE-IN plugs to connect line-level instruments such as keyboards, drum machines 
and effect devices. 
NOTE: Never try to connect a line-level signal to the XLR MIC input when the 
phantom power is engaged or you may seriously damage your equipment.

2- STEREO LINE INPUTS
These are channels 3/4, and 5/6. They are organised in stereo pair and provided 
with 1/4" TRS phone sockets. If you connect only the left jack, the input will operate 
in mono mode, that's mono signal will appear on both input channels. You can use 
these inputs with a stereo keyboard, drum machine, etc.

3- TRIM
This control is provided with 2 different indication rings: one is for the MIC and the 
other for the LINE input. When you use a Microphone, you shall read the MIC ring 
(0~50 dB); when you use a line level instrument, you shall read the LINE ring 
(+15~-30dB). For optimum operation, you shall set this control in a way that the 
PEAK LED will light up only occasionally in order to avoid distortion on the input 
channel.

4- STEREO AUX RETURNS
You can use these stereo 1/4" phone sockets to return the stereo signal of an effect 
unit to the Main Mix. Alternatively you can use them as an extra auxiliary input and 
using the AUX RETURN level control as volume control. The signal will be sent 
directly to MAIN MIX control.

5- AUX SEND
This 1/4" phone socket is used to send out the signal from AUX bus of the input 
channels into external devices such as effect units and/or stage monitors. AUX 
SEND is wired post-fader to control the signal of the internal multi-effects unit. You 
can also connect an external effect unit. In such case, the internal effect unit will 
be automatically disconnected. If you want to wire the AUX circuit as pre-fader, 
read Chapter 6. of this Manual. In the pre-fader mode, the AUX bus can send the 
signal to a stage monitor.

6- PHONES
This socket will be used to send the signal to a pair of headphones.

7- CTRL ROOM OUTPUT
These 1/4" phone sockets will be used to send the signal to a pair of powered 
Studio Monitor speakers or to a second set of PA.

8- MAIN MIX OUTPUTS
This stereo output is controlled by the Main Mix Level on  Master section and will 
send the audio signal to an amplifier or to a pair of active speakers. The output 

level can be varied from -∞ to +15 dB.

Summary of Contents for MXI Series































Reviews: