background image

 

• Do not allow persons or children to remain in the automation operation area. 

• Keep radio control or other control devices out of children’s reach, in order to avoid unintentional 

automation activation. 

• The user must avoid any attempt to carry out work or repair on the automation system, and always request 

the assistance of qualified personnel. 

• Anything which is not expressly provided for in the present instructions is not allowed. 

•  Before installing the gate opener, check that all moving part as well as the sliding gate is in good 

mechanical condition, correctly balanced and opens and closes properly. 

• Save these instructions for future use. 

 

Preparation for Installation 

Before proceeding to your opener installation, check if your gate structure is in accordance with the current 

standards, especially as follows: 

The gate sliding track is linear and horizontal, and the wheels are suitable

the gate should be mounted and 

moving freely. Check that the structure is sufficiently strong and rigid, Make sure that the gate is plumb and 

level. The fence posts must be mounted in concrete. The gate does not bind or drag on the ground. 

• The opening and closing gate stops are positioned. 

 

WARNING: 

Remember  that control devices are intended to facilitate gate operation, but can not 

solve problems due to any defects or deficiency resulting from failure to carry out correct installation or 

maintenance. Take the product out of its packing and inspect it for damage. Should it be damaged, contact 

your dealer. Remember to dispose of its components (cardboard, polystyrene, nylon, etc.) according to the 

current prescriptions. 

Refer to the following Figures for gate installation. 

 

In sake of safety, a positive stop must be mounted on the two end of ground track. 

 

Summary of Contents for CK700



















Reviews: