background image

25

ERROR ABOUT INSTRUMENT

If errors still persist after attempting to clear them, contact your local 
TOPCON dealer.

Display

Explanation

Countermeasure

Comp Err

The inclination of the instrument 
exceeds the capacity of  the compen-
sator.

Level the instrument properly.

Dark Err

The level cannot read the rod due to 
lack of light.

The data will have to be entered 
manually until lighting has 
improved.

Light Err

The level cannot read the rod due to 
an excess of light such as direct sun-
light or glare.

Remove the source of the sunlight 
or glare from the objective lens.

ROM Err

This message is displayed when any 
abnormality occurs with internal 
memory.

Turn the power switch off  then on 
again.

CCD Err

Any abnormality occurs within the  
CPU.

Turn the power switch off  then on 
again.

No Staff

Level is not properly sighted on the 
staff.

Collimate the staff properly.

Meas Err

• The distance between the instru-

ment and the staff is either too far or 
near.

• The staff is obstructed by more than 

30 percent.

• The cross-hairs are not within the 

range of  the staff.

• The distance between the instru-

ment and the staff should be 
within  the range of  2m to 60m. 
(Fiberglass staff)

• Remove the obstructions.

• The staff should be within the 

range of the cross-hairs.

CPU Err

Any abnormality occurs within the  
CPU.

Turn the power switch off  then on 
again.

COMM Err

Communication Error

Confirm the setting of communica-
tion and try to communicate again.

Coll Err

An invalid value has been collected 
during the adjustment process.

Start the adjustment procedure 
from the beginning.

Opr Err

Level is not properly sighted during 
the adjustment process.

Start the adjustment procedure 
from the beginning.

Setting Err

Level is not set approximately during 
the adjustment process.

Set the instrument approximately 
Start the adjustment procedure 
from the beginning.

Focus Err

Auto focus does‘t function precisely.

Measure again. But auto focus 
doesn‘t function precisely,  use 
manual  focus.

Summary of Contents for DL-103 Series




































Reviews: