Operating elements
1 Air control knob
Low - Hi
2 On/off switch
I/O
3 Filter holder
4 Stand/hanger
5 Adjustable angle knob
6
Activated carbon filter *
7 Power cable with mains plug
(not shown)
Operation
a) Setting up the product
•
Place the product on a stable and flat surface using the provided stand (4) or hang it on
suitable support beam that can withhold product weight of approx. 1 kg.
• Adjust the desired blowing/absorption angle using the adjustable angle knob (5).
• Connect the mains plug (7) to an appropriate mains socket.
b) Using as a table fan
To increase performance, remove the filter from the filter holder (3) located on the
back of the product.
• Switch the product on by setting the on/off switch
(2) to
I
position.
• Adjust the blowing power using the air control knob
Low - Hi
(1).
• After use, switch the product off by setting the on/off switch to
O
position.
c) Using as a smoke absorber
Before using as an absorber, make sure that the activated carbon filter (6) is clean
and has been correctly installed.
• Reverse and aim the back side of the product towards the solder smoke. Set up the product
as close to the soldering site as possible.
• Switch the product on by setting the on/off switch to
I
position.
• Adjust the absorption power using the air control knob
Low - Hi
.
• After use, switch the product off by setting the on/off switch to
O
position.
Care and cleaning
a)
Changing the activated carbon filter *
Change the activated carbon filter regularly when it becomes visibly dirty in order to
ensure that the product works effectively.
•
To remove the activated carbon filter, simply pull it out from the filter holder (3) located on the
back of the product.
•
Install new filter in a reverse order.
b) Cleaning
•
Apart from the occasional filter change, the product is maintenance-free.
• Disconnect the product from the power supply before cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
•
Clean the outside of the product with a soft, dry, fiber-free cloth.
• Do not immerse the product in water.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Input voltage ................................. 220 - 240 V/AC, 50 Hz
Rated power ................................ 23 W
Protection class ............................ I
Noise level .................................... 42 - 45 dB
Absorption capacity ...................... max. 0.2 - 1 m³/minute
Blowing capacity ........................... max. 0.2 - 1.2 m³/minute
Cable length ................................. approx. 1.4 m (without plug)
Operating conditions ..................... -6 to +46 ºC, 10 % – 90 % RH
Storage conditions ........................ -20 to +60 ºC, 10 % – 70 % RH
Dimensions (W x H x D) ............... 217 x 185 x 135 mm
Weight .......................................... 1042 g
* Replacement filter (Item no. 588546) can be purchased from: www.conrad.com
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*1553619_V1_0817_02_mxs_m_en
4
5
2
1
6
3
