This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication reflects the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
*1881818_v1_0119_02_DS_m_4L_(1)
Setup
•
Slide the on/off switch (3) to the
ON
position to switch the laser on. Switching on the laser
automatically unlocks the levelling pendulum. This enables the cross-line laser to level itself
automatically.
•
After turning on the on/off switch (3), the horizontal laser beam will appear at an angle of 360°
around the cross-line laser. The cross-line laser is now in the default mode.
•
To switch off the laser, slide the on/off switch (3) to the
OFF
position. Switching off the laser
automatically locks the levelling pendulum.
•
When the on/off switch (3) is in the
OFF position
, press and hold the laser power button (4)
for approximately 3 seconds to switch the laser on.
•
In this mode, the automatic levelling feature cannot be used. You can now adjust the cross-
line laser in angles of more than 4°. This feature can be used to project and mark different
points, e.g. angles or slanted lines, or to connect two points on walls that are not on a
horizontal line.
The levelling pendulum features a lock that helps to protect against damage from
shaking or impacts during transport.
Configuration options
The cross-line laser features two different modes:
- Self-levelling laser beam
- Laser device for marking points (in this mode, the levelling function is disabled)
Dim the ambient lighting to ensure that you can easily detect the laser beam.
a) Using the levelling function
•
Place the cross-line laser on a horizontal surface with an inclination of less than 4°. The
self-levelling function stops working when this limit is exceeded. You can screw the cross-line
laser to a suitable tripod with a 1/4" thread (not included). Ensure that the tripod is aligned
horizontally within the 4° tolerance limit. The laser will be automatically aligned in a vertical
position.
If the cross-line laser is inclined at an angle of more than 4°, the laser will flash to
warn you that the pendulum cannot offset the inclination.
•
Press the laser power button (4) once to switch to the vertical laser. The vertical laser beam
will appear and the horizontal laser beam will switch off. The laser beam will only appear on
the side of the laser projector (vertical) (1).
•
Press the laser power button (4) again to switch on the horizontal laser beam. The vertical
and horizontal laser beams will appear together and form a cross-line projection.
•
Press the button again to switch back to the default mode. The horizontal laser line will
appear.
b) Using the laser without the levelling function
•
Position the cross-line laser on a surface at the desired angle in order to configure the angle
of the beam(s).
•
You can screw the cross-line laser to a suitable tripod with a 1/4" thread (not included) and
adjust the angle as desired.
•
Slide the on/off switch (3) to the
OFF
position to switch off the laser and lock the levelling
pendulum.
•
Hold down the laser power button (4) for 2–3 seconds to switch on the laser without the
levelling function. The horizontal laser beam will flash slowly to indicate that the levelling
function is disabled.
•
Press the laser power button (4) once to switch to the vertical laser beam. The vertical laser
beam will start to flash and the horizontal laser beam will switch off. The vertical beam will
only appear on the side of the laser projector (vertical) (1).
•
Press the laser power button (4) a second time to switch to the horizontal laser beam. The
vertical and horizontal laser beams will appear together and form a cross-line projection.
•
Press the button for a third time to switch the laser off. The laser beams will disappear.
Care and cleaning
•
Before cleaning the product, disconnect it from the power supply by removing the batteries.
•
Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the housing or cause the product to malfunction.
•
Use a dry, lint-free cloth to clean the product.
•
Store and transport the product in the storage pouch provided.
Disposal
a) Product
Electronic devices are recyclable waste and must not be placed in household
waste. At the end of its service life, dispose of the product according to the relevant
statutory regulations.
Remove any inserted batteries and dispose of them separately from the product.
b) Battery information
You are required by law to return all used batteries (Battery Directive). They must not
be placed in household waste.
Batteries containing hazardous substances are labelled with this symbol to indicate
that disposal in household waste is forbidden. The abbreviations for heavy metals
in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (indicated on the battery,
e.g. below the waste bin icon on the left).
Used batteries can be returned to local collection points, our stores or battery retailers.
You thus fulfil your statutory obligations and contribute to environmental protection.
Technical data
Power supply ................................ 4x AA batteries
Working range
.............................. Up to 18 m
Accuracy ....................................... ±5 mm (at 10 m)
Battery life ..................................... 10 h (130 mA battery)
Laser class
................................... 2
Laser output power
.......................
1 mW
Laser wave length
........................
635 nm
Tripod thread
................................ 6.35 mm (1/4")
Protection rating
........................... IP54
Operating conditions ..................... -10 to +40 °C
Storage conditions ........................ - 20 to +60 °C
Dimensions (L x W x H) ................ 106.5 x 66.5 x 117.5 mm
Weight
.......................................... 503 g