manualshive.com logo in svg

Tomahawk JXPT24K, Operation Manual

The Tomahawk JXPT24K Operation Manual is a comprehensive guide to effectively operate and maintain your Tomahawk JXPT24K. This manual is essential for trouble-free usage and is available for free download at manualshive.com, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

6

1.2.9 ALWAYS 

operate machine with all safety devices and guards in place and in working 

order. DO NOT modify or remove safety devices. DO NOT operate machine if any safety 

devices or guards are missing or inoperative.

1.2.10 ALWAYS 

read, understand, and follow procedures in Operator's Manual before 

attempting to operate equipment.

1.3  Safety while using Combustion Engines

 

            Internal combustion engines present special hazards during operation and fueling!                   

            Read and follow warning instructions in engine owner's manual and safety guidelines 

below. Failure to follow warnings and DANGER safety guidelines could result in severe 

injury or death.

1.3.1 DO NOT 

run machine indoors or in an enclosed area such as a deep trenches unless 

there is adequate ventilation, through such items as exhaust fans or hoses are provided. 

Gasoline exhaust from the engine contains poisonous carbon monoxide gas; exposure to 

carbon monoxide can cause loss of consciousness and may lead to death.

1.3.2 DO NOT 

smoke while operating machine.

1.3.3 DO NOT 

smoke when refueling engine.

1.3.4 DO NOT

 refuel hot or running engine.

1.3.5 DO NOT 

refuel engine near open flame.

1.3.6 DO NOT 

spill fuel when refueling engine.

1.3.7 DO NOT 

run engine near open flames.

1.3.8 ALWAYS 

refill fuel tank in well-ventilated area.

1.3.9 ALWAYS 

replace fuel tank cap after refueling.

1.3.10 ALWAYS 

check fuel lines and fuel tank for leaks and cracks before starting engine. 

1.3.11 DO NOT 

run machine if fuel leaks are present or fuel lines are loose.

1.4  Service Safety

 

             Poorly maintained equipment can become a safety hazard! In order for the

             equipment to operate safely and properly over a long period of time, periodic 

maintenance and occasional repairs are necessary.

1.4.1 DO NOT

 attempt to clean or service machine while it is running. Rotating parts can 

cause severe injury.

1.4.2 DO NOT

 crank a flooded engine with the spark plug removed on gasoline-powered

engines. Fuel trapped in the cylinder will squirt out the spark plug opening.

DANGER

WARNING

Summary of Contents for JXPT24K













































Reviews:

No comments

Related manuals for JXPT24K

Brands by name

Popular brands

Load more brands