3800 County Road 116, Hamel, MN 55340
http://www.Tolomatic.com • Email: [email protected]
Phone: (763) 478-8000 • Fax: (763) 478-8080 • Toll Free: 1-800-328-2174
8
© 2017 Tolomatic
201702031046
Information furnished is believed to be accurate
and reliable. However, Tolomatic assumes no
responsibility for its use or for any errors that
may appear in this document. Tolomatic reserves
the right to change the design or operation of the
equipment described herein and any associated
motion products without notice. Information in
this document is subject to change without notice.
4 – Switches / Maintenance
MXP25P
Parts Sheet #8100-4106_06_MXP25Pps
SWITCH WIRING DIAGRAMS AND LABEL COLOR CODING (CE and RoHS Compliant)
NORMALLY
CLOSED
BRN
BLU
+
-
LOAD
NORMALLY
CLOSED
BRN
BLU
+
-
LOAD
or
NORMALLY
OPEN PNP
(SOURCING)
BRN
BLK
+
SIGNAL
LOAD
BLU
-
NORMALLY
OPEN NPN
(SINKING)
BRN
BLK
+
SIGNAL
LOAD
BLU
-
NORMALLY
CLOSED PNP
(SOURCING)
BRN
BLK
+
SIGNAL
LOAD
BLU
-
NORMALLY
CLOSED NPN
(SINKING)
BRN
BLK
+
SIGNAL
LOAD
BLU
-
NORMALLY
OPEN
BRN
BLU
+
-
LOAD
NORMALLY
OPEN
BRN
BLU
+
-
LOAD
or
TY • TK
SOLID STATE • NORMALLY OPEN • PNP
NY • NK
REED • NORMALLY CLOSED
QUICK DISCONNECT MALE PLUG PINOUT
#8100-9080 QUICK DISCONNECT
FEMALE SOCKET PINOUT
RY • RK
REED • NORMALLY OPEN
KY • KK
SOLID STATE • NORMALLY OPEN • NPN
PY • PK
SOLID STATE • NORMALLY CLOSED • PNP
HY • HK
SOLID STATE • NORMALLY CLOSED • NPN
BROWN (+)
BLUE (-)
BLACK
(SIGNAL)
BLUE (-)
BROWN (+)
BLACK
(SIGNAL)
SWITCH DETECTION POINT
16, 25, 32
MOUNTING DIMENSIONS
SWITCH DIMENSIONS
40, 50, 63
1.18 [30]
.31 [8]
Ø.28 [7]
.95 [24.1]
1.26 [32.1]
.51 [13]
DETECTION POINT REED
DETECTION POINT
SOLID STATE
13.35 [339]
M8x1
M8x1
197 [5000]
197 [5000]
_
K
- QD (Quick-disconnect) switch
8100-9080 - QD Cable
_
Y
- direct connect
U
SWITCHES SIT BELOW
TUBE EXTRUSION PROFILE
SWITCHES SIT BELOW
TUBE EXTRUSION PROFILE
V
U
Ø.35
[9]
W
V
X
Switches for MX:
• Include retained mounting hardware
• In slot, sit below extrusion profile
• Same for all sizes and bearing styles
LUBRICATION AND MAINTENANCE
All Tolomatic MX Band Cylinders are prelubricated at the factory. To ensure
maximum cylinder life, the following guidelines should be followed.
1. Filtration
We recommend the use of dry, filtered air in our products. “Filtered air”
means a level of 10 Micron or less. “Dry” means air should be free of
appreciable amounts of moisture. Regular maintenance of installed filters
will generally keep excess moisture in check.
2 External Lubricators (optional)
The factory prelubrication of Tolomatic Band Cylinders will provide optimal
performance without the use of external lubrication. However, external
lubricators can further extend service life of pneumatic actuators if the
supply is kept constant.
Oil lubricators, (mist or drop) should supply a minimum of 1 drop per 20
standard cubic feet per minute to the cylinder. As a rule of thumb, double
that rate if water in the system is suspected. Demanding conditions may
require more lubricant.
If lubricators are used, we recommend a non-detergent, 20cP @ 140˚F
10-weight lubricant. Optimum conditions for standard cylinder operation
is +32˚ to +150˚F (+0˚ to 65.5˚C).
NOTE:
Use of external lubricators may wash away the factory installed
lubrication. External lubricants must be maintained in a constant supply or
the results will be a dry actuator prone to premature wear.
3. Sanitary Environments
Oil mist lubricators must dispense “Food Grade” lubricants to the air
supply. Use fluids with ORAL LD50 toxicity ratings of 35 or higher such
as Multitherm
®
PG-1 or equivalent. Demanding conditions can require a
review of the application.
4. Cushion Adjustment
Adjust the Cushion Needles in the Cylinder Heads carefully to obtain opti-
mum deceleration for your particular application. If there are questions on
proper adjustment, please consult Tolomatic.
SWITCH INSTALLATION AND REPLACEMENT
Place switch in side groove on tube at desired location with "Tolomatic" facing
outward. While applying light pressure to the switch, rotate it such that the switch is
halfway in the groove. Maintaining light pressure, rotate the switch in the opposite
direction until the switch is fully inside the groove with "Tolomatic" visible. Re-position
the switch to the exact location and lock the switch securely into place by tightening
the screw on the switch.
Insert
switch
Rotate
switch
Secure
switch
Tolo
mat
ic
Tolo
mati
c
Tolom
atic
Dimensions in inches [brackets indicate dimensions in millimeters]
