The battery is not charged enough at the time of purchase. When you
use for the first time or “Charge required” is displayed because of the
low battery level, charge it to use.
Check the direction of the charging terminals carefully to charge
them.
Fit the wristwatch receiver into the charger firmly. Inadequate fitting
can cause the charge from stopping halfway through.
Do not charge with the wristwatch receiver wet. It may cause electric
shock, failure and fire. The failure due to charging in wet is out of
warranty, not repairable.
Do not charge near water, source of fire, or things that are fragile. It
may cause electric shock, failure and fire. The failure due to
charging in wet is out of warranty, not repairable.
If you charge the battery by the head of a bed or near things that are
fragile, be careful for a tumble or fall.
①
Put the left side of the wristwatch receiver into the electrodes of the
charger and press the right side of the receiver. (Fig. 1)
②
Lower the wristwatch receiver and adjust the position of the charging
terminal. (Fig. 2)
③
“Charging” is displayed on the LCD screen of the wristwatch receiver
and it starts charging. (Fig. 3)
* For charging, make sure to put up the stand as Fig. 3 to use.
Battery Life on Charging
In case of full charge, the battery lasts for about 4 days on reception
of 5 or 6 times per day.
The built-in battery of the wristwatch receiver is a consumable
supply. It is time for replacement when the usable time with a full
charge gets extremely short. Please contact us or your vendor.
* Do not replace the battery on your own.
How to Check Charging Timing
When Charge required is displayed on the wristwatch receiver,
charge the battery soon.
Full
Half
Charge
required Empty
When the battery icon is empty, it gets unreceivable and the power
turns OFF.
We recommend to charge the battery before the battery icon is
empty.
Preparation for Using Silwatch
Charge the Wristwatch Receiver
Using Charger / Integrated Adapter
(Fig. 1)
(Fig. 2)
(Fig. 3)
Set the both terminals of the charger and
the receiver to fit properly.
■
Message Display While Charging
・
While charging, you can check if it is charged by the blinked
message “Charging”.
・
While charging, the Alarm function and the Buzzer function are OFF
regardless of the settings.
・
While charging, the normal reception function is OFF (without
antenna icon).
* You can change on “Set while charging”. (Page 20)
* When “Set while charging” is ON, a received message is
displayable even while charging.
* Check “Set while charging.” (Page 20)
■
Caution on handling charger
・
Trash or dirt on the charging terminals of the receiver and the
charger can cause hard to charge, so wipe them clean with a soft
cloth, etc. before charging. Before cleaning the charging terminals,
unplug the power cord just in case.
・
The charging is complete in about 3 hours. (The charging is
complete in about 3 hours. * At Default Setting)
・
Long press the MENU button (for about 2 seconds) turns the power on.
* For how to turn on the power, refer to page 9.
7
8
・
The receiver cannot receive for about 3 minutes after putting it into
the charger. (The mark is not also displayed.)
* In case “Set while charging” is ON
・
Depending on the model, it is receivable right after starting charging
( mark displayed).
* For the details, refer to “Set while charging” on page 20.
■
Integrated AC Adapter
The cord of the AC adapter is shipped in a small and rounded state; a
long time use of the cord with it kept bent can cause breaking of wire
due to deformation of the cord. Use the AC adapter with the cord as
straight as possible, especially get the both ends straight to use.
■
Cleaning Charger
・
Soak the alcohol in a cotton swab, etc. to clean the dirt of the
electrodes.
* Recommended goods: Alcohol for fuel with a concentration of
90% or more and cotton swabs
* Warning: Do not ever short the electrodes.
(Do not use) Lubricant CRC556, etc., gasoline, petroleum,
kerosene
Do not ever short
the electrodes.
Receiver terminal
Terminal of the
charger
Charging