Toho Electronics TTM-339, Operation Manual, Page: 24 / 32

- 24 -
5.6 Common parameter setting mode SET 5 to 8
SET05
to
SET08
Name Setting content Initial value
1
E
*
F1
Event function 1 setting
Function Add-on function
00
*0 None 0* None
*1 Deviation upper and lower limits 1* Hold
*2 Deviation upper limit 2* Standby
*3 Deviation lower limit 3* Delay
*4 Deviation range 4* Hold + standby
*5 Absolute value upper and lower limits 5* Hold + Delay
*6 Absolute value upper limit 6* S Delay
*7 Absolute value lower limit 7* Hold + s Delay
*8 Absolute value range
2
E
*
H
Event upper limit setting
Thermocouple/RTD input -1999.9 to 2999.9 ( ° C) -1999 to 2999 ( ° C) Note that for
R, B and PR40-20 of thermocouple, the following is to be applied. -1999 to 9999 ( ° C)
0
Current/voltage input -19999 to 29999 (digit)
3
E
*
L
Event lower limit setting
Thermocouple/RTD input -1999.9 to 2999.9 ( ° C) -1999 to 2999 ( ° C) Note that for
R, B and PR40-20 of thermocouple, the following is to be applied. -1999 to 9999 ( ° C)
0
Current/voltage input -19999 to 29999 (digit)
4
E
*
C
Event sensitivity setting
Thermocouple/RTD input 0.0 to 999.9 ( ° C) 0 to 999 ( ° C)
0
Current/voltage input 0 to 9999 (digit)
5
E
*
T
Event Delay timer setting 0 to 9999 (second) 0
6
E
*
F2
Event function 2 setting
(loop abnormality)
Function Add-on function
00 *0 Nonexistent 0* None
*1 Existent 1* Hold
7
E
*
P
Event polarity setting 0 Normal open 1 Normal close 0
5.7 Common parameter setting mode SET 9 (1)
SET09
Name Setting content Initial value
1
MLF
Operation amount function
setting
0 None 2 Operation amount current limiter(average)
0
1 Operation amount limiter 3 Operation amount current limiter(R.M.S)
With the selection of [
MLF
=1], the following 2 to 9 are selectable for [CNT =1]; the following 2 to 17 are selectable for [
CNT
= 3 or 4].
* Below, 2 and 3 are for the operation amount limiter function setting, i.e., effective when 1 is selected.
2
MLH11
Primary control operation amount limiter upper limit 1
MLL11
to 100.0(%) 100.0
3
MLL11
Primary control operation amount limiter lower limit 1 0.0 to
MLH11
(%)
0.0
* Below, 4 and 5 are for the operation amount limiter function setting, i.e., effective when 2 is selected.
4
MLH21
Primary control operation amount limiter upper limit 2
MLL21
to 100.0(%) 100.0
5
MLL21
Primary control operation amount limiter lower limit 2 0.0 to
MLH21
(%) 0.0
* Below, 6 and 7 are for the operation amount limiter function setting, i.e., effective when 3 is selected.
6
MLH31
Primary control operation amount limiter upper limit 3
MLL31
to 100.0(%) 100.0
7
MLL31
Primary control operation amount limiter lower limit 3 0.0 to
MLH31
(%) 0.0
* Below, 8 and 9 are for the operation amount limiter function setting, i.e., effective when 4 is selected.
8
MLH41
Primary control operation amount limiter upper limit 4
MLL41
to 100.0(%)
100.0
9
MLL41
Primary control operation amount limiter lower limit 4 0.0 to
MLH41
(%) 0.0
* Below, 10 and 11 are for the operation amount limiter function setting, i.e., effective when 1 is selected.
10
MLH12
Secondary control operation amount limiter upper limit 1
MLL12
to 100.0(%) 100.0
11
MLL12
Secondary control operation amount limiter lower limit 1 0.0 to
MLH12
(%) 0.0
* Below, 12 and 13 are for the operation amount limiter function setting, i.e., effective when 2 is selected.
12
MLH22
Secondary control operation amount limiter upper limit 2
MLL22
to 100.0(%) 100.0
13
MLL22
Secondary control operation amount limiter lower limit 2 0.0 to
MLH22
(%) 0.0
* Below, 14 and 15 are for the operation amount limiter function setting, i.e., effective when 3 is selected.
14
MLH32
Secondary control operation amount limiter upper limit 3
MLL32
to 100.0(%) 100.0
15
MLL32
Secondary control operation amount limiter lower limit 3 0.0
～ MLH32
(%) 0.0
* Below, 16 and 17 are for the operation amount limiter function setting, i.e., effective when 4 is selected.
16
MLH42
Secondary control operation amount limiter upper limit 4
MLL42
to 100.0(%) 100.0
17
MLL42
Secondary control operation amount limiter lower limit 4 0.0 to
MLH42
(%) 0.0