Anti Rolling Gyro
Model:MSM-17500T-A1
－
22
－
Table 5-1 Fault finding table for the
ARG
No.
Problem
Possible cause
Step to take
4
Rotation rate
check lamp does
not light on.
Lamp bulb has blown.
・
Change the lamp bulb.
Connection failure.
・
Check the start check lamp wiring is not
open- circuited.
5
The
ARG
stops
after turned on or
during the
operation
Power generator is not
producing enough
power.
・
Check the capacity of the power generator,
which must exceed the mass of the total
ARG
’s power used.
・
The power generator to supply the
ARG
is
also used for another equipment, which
consumes big amount of electricity, and it
causes the power generator produce to
produce insufficient power.
Electric shutdown
because other
equipment is turned on.
・
If other equipment is turned on, it decreases
the voltage momentary and it stops the
ARG
.
Please turn on the equipment first, and then
turn the
ARG
on.
Operation of the safety
device
・
When the
ARG
is operated under high
ambient temperature, stormy weather or
excessive high wave conditions, the
ARG
may stop.
Cool the ambient temperature by ventilation,
and contact the Sales Agent.
6
GPS
, radio or
other equipment
makes noise after
the
ARG
is in
operation.
The
ARG
’s noise is
affecting other
equipment’s noise.
・
Keep the distance between other equipment
and the
ARG
and/or its wirings.
(Noise may
be superimposed on AM radio depending on
the location.)
・
Check the ground lead between the
ARG
and the ship.
・
Adjust sensitivity when the image of the Fish
Finder is noisy and distorted. Refer to the
operation instructions of the Fish Finder.
7
During operating
ARG by
generator power
supply,electronic
devices such as
IH does not start.
The
ARG
's power
harmonic is affecting
other equipment.
・
Increase the number of AC power devices (air
conditioners, water heaters, etc) to be used.
8
The
ARG
makes
unusual noise or
vibration.
Selected wrong
rotational direction.
・
Make sure that the serial numbers of the
ARG
unit and the Motor Driver are the same.
Effect of resonance
・
There is a mechanical resonance point in the
ARG
during the time that rotational speed
becomes steady. Please wait until it becomes
steady rotational speed.
・
If there is a resonance in the hull or wall, take
appropriate measures to increase the
strength and rigidity of the material of the hull
or wall.
Effect of environmental
temperature.
・
When the environmental temperature is low,
the bearings might make some noise
especially just after the starting. Wait until the
rotational speed becomes steady, and then
make sure that it does not make the noise
any longer.
Summary of Contents for ANTI ROLLING GYRO ARG175T
