background image

12. SPECIFICATIONS

Note: Change of design and specifications without prior notice possible.  

• Options

Surface-mount box: OW-101  ...................................................  1 

Flush-mount box: IW-101 .........................................................  1 

Model

RS-410EC e

Rated Input

1 W

Audio Frequency Range

 300Hz – 7kHz

Speech Method

 Hands-free conversation

Hands-free

Speaker: 3,5cm (1.38“) cone-type, maximum output 0,5W, 8Ω

Microphone: Omni-directional electret condenser microphone

Push-button Standard

Momentary, stainless steel, silver

Push-button Emergency

Momentary, red (blinks red during calling, lights during conversation)

Description Emergency

Protective pane

Operation Indicator

1 LED

Wiring

Twisted pair cables (2x pair)

Transmission Range 

1km / Ø 0,5mm (AWG24)

1,5km / Ø 0,65mm (AWG22)

2km / Ø 0,9mm (AWG19)

Installation Method

Flush-mount / Surface-mount

Housing Protection

IEC 62262: IK10

Dust/ Water Protection

EN 60529: IP 65. (panel edges must be sealed at installation)

Operating Temperature

-10°C to 50 °C

Operating Humidity

Under 90 % RH (condensation free)

Finish

Front plate: Aluminum

Call-buttons: Steel

Dimensions

150 (W) x 247 (H) x 45 (D) mm

Weight

0.6 kg

Traceability Information for Europe (EMC directive 2004/108/EC)

Manufacturer: 

TOA Electronics Europe GmbH 

Suederstrasse 282, 20537 Hamburg, Germany   

Authorised representative

TOA Electronics Europe GmbH 

Suederstrasse 282, 20537 Hamburg, 

Germany  

 http://www.toa.de/ 

833TEERZ1603b 

Summary of Contents for RS-410EC e











Reviews: