TMI Products BELAIR-SC8 Owner'S Manual Download Page 4

LIMITED WARRANTY

4

All equipment and accessories are thoroughly inspected and tested before leaving the factory. They are warrantied to 

be free of defects from workmanship and materials for one year from date of original purchase. (proof of purchase is 

required).

 

Labor: 90 days from initial purchase

Parts: 1 year, excluding normal wear and tear items

Heavy duty fiber composite body: 20 years limited warranty

Polyethylene body: 5 years limited warranty

 

Should  any  trouble  develop  during  this  period,  please  contact  your  dealer  or  manufacturer  to  receive  a  Return 

Guarantee Authorization number (RGA #). Return the part or extractor that need to be replaced. If after an inspection 

it  is  determined  to  be  under  warranty,  the  factory  will  repair  or  replace  (manufacturer’s  discretion)  the  parts  or 

equipment and return parts or equipment at no charge.  Note: Credit, repair or replacement will not be given to any 

parts or equipment without the above mentioned RGA#.   

 

 

Proof of purchase is necessary to establish the date of the original sale. Receipt of purchase or warranty registration 

can be used as proof of purchase. It is important to register your purchase by sending the warranty registration form 

within 10 days of purchase.

 

This warranty is in lieu of all other warranties expressed or implied, and no person is authorized to give any other 

warranty, assume obligation or liability on the manufacturer’s behalf.

This Warranty does not apply when: 

Repairs that are required because of normal wear and tear

Repairs have been made or attempted by others

Items have been abused, misused or improperly maintained

Modifications or alterations have been made to the equipment

In  no  event  shall  seller  be  liable  for  any  incidental,  consequential  or  special  damages  of  any  kind  or  nature 

whatsoever. Including but not limited to lost profits arising from or in anyway connected with this agreement or items 

sold  hereunder,  whether  alleged  to  arise  from  breach  of  contract,  express  or  implied  warranty,  or  in  tort,  including 

without limitation, negligence, failure to warn or strict liability.

LIMITATION OF REMEDY:

This agreement and warranty shall be governed in all respects by the law of the State of Massachusetts. No actions 

arriving out of the items sold hereunder or this Agreement may be brought by either party more than two (2) years 

after the cause of action occurs. All mediation or litigation will take place in the County of Middlesex in Massachusetts. 

ENTIRE AGREEMENT / GOVERNING LAW:

Summary of Contents for BELAIR-SC8























Reviews: