background image

7

Power Input/Output

Converter

•  AC-fed 12- or 24-pulse diode rectifier using externally 

mounted phase shifted transformer; no harmonic filter 
required to meet IEEE 519 guidelines

•  DC bus voltage:  3 x 5,700 Vdc
•  Power factor greater than 95% in speed control range

Inverter

•  Three-level inverter for motor friendly wave form
•  Uses 4 GCT devices for each of three phases
•  3.8 kV output to motor – no output transformer 

required

•  Inverter power modules water cooled
•  Conservative design for expected 20 year MTBF

Input Voltage

Any utility voltage using 
separate transformer input

50/60 Hz ±10%

Output Voltage

3,800 Vac

Output Current

2400 A rms

Output Frequency

50-60 Hz

Output Chopping

600 Hz (max)

Drive Effi ciency

98%

Cable Entry

Top or bottom access

A Clean Output Wave

As a result of the three-level PWM control, the output 
current waveform is close to a sine wave.  Harmonic 
currents in the motor are minimized so the heat loss is 
negligible and there is very little torque ripple on the 
output shaft.

Protective Functions Include

• Inverter overcurrent
• Inverter overvoltage
•  Low system voltage
•  Motor ground fault
• Motor overload
• Cooling fan abnormal
• Over-temperature

• CPU error
•  Water cooling alarm
• Exciter fault
•  DC voltage drop
• Motor inverse rotation
• Stall detection 
• Ground detection

Frequency Control

• Volt/Hertz Control 
• Vector control
•  Power factor control for synchronous motors

Output Voltage  Modulation

The output switching modulation strategy is dynamically 
adjusted based on three speed zones to minimize motor 
torque pulsation.

Drive Inputs

•  LAN Interface Options:  Profibus-DP, DeviceNet, 

Modbus RTU, TOSLINE S-20

•  Input/Output:  6 Analog I/O, 8 Digital I/O

Power Circuits

Motor Control

Gate Commutated Thyristor 
(GCT) with driver board.  
Rated 6,000 Volts, 6,000 
Amps - the world’s largest 
switching device.

TMdrive-XL80 – 15 MVA Frame

Power Rating:

 

15 MVA, expandable to 30 MVA

Output Voltage:

 3.8 

kV

Output Frequency:

 

Rated 50-60 Hz, 50 to 200 Hertz 
option with derate above 100 Hz

Dimensions

Width 4.8 m; Height:  2.7 m

Motor type:

 

Synchronous or Induction

XLdrive Series Family Application Guide.indd   7

10/3/2011   3:16:15 PM

Summary of Contents for TMdrive-XL Series









Reviews: